DataSheet39.com

What is MAX6881?

This electronic component, produced by the manufacturer "Maxim Integrated Products", performs the same function as "(MAX6880 - MAX6883) Power-Supply Sequencers/Supervisors".


MAX6881 Datasheet PDF - Maxim Integrated Products

Part Number MAX6881
Description (MAX6880 - MAX6883) Power-Supply Sequencers/Supervisors
Manufacturers Maxim Integrated Products 
Logo Maxim Integrated Products Logo 


There is a preview and MAX6881 download ( pdf file ) link at the bottom of this page.





Total 19 Pages



Preview 1 page

No Preview Available ! MAX6881 datasheet, circuit

www.DataSheet4U.com
19-3772; Rev 1; 10/05
Dual-/Triple-Voltage, Power-Supply
Sequencers/Supervisors
General Description
The MAX6880–MAX6883 dual-/triple-voltage monitors
are designed to sequence power supplies during
power-up condition. When all of the voltages exceed
their respective thresholds, these devices turn on volt-
ages to the system sequentially, enhancing n-channel
MOSFETs used as switches. The time between each
sequenced voltage is determined by an external
capacitor, thus allowing flexibility in delay timing. The
MAX6880/MAX6881 sequence three voltages and the
MAX6882/MAX6883 sequence two voltages.
These devices initially monitor all of the voltages and
when all of them are within their tolerances, the inter-
nal charge pumps enhance external n-channel
MOSFETs in a sequential manner to apply the volt-
ages to the system. Internal charge pumps drive the
gate voltages 5V above the respective input voltage
thereby ensuring the MOSFETs are fully enhanced to
reduce the on-resistance.
The MAX6880–MAX6883 feature capacitor-adjustable
slew-rate control to provide controlled turn-on charac-
teristics. After all of the voltages reach 92.5% of their
final value, a power-good output (MAX6880/MAX6882)
signal is active. The power-good output (PG/RST) can
be delayed with an external capacitor to create a
power-on reset delay. After the initial power-up phase,
the MAX6880–MAX6883 continue to monitor the volt-
ages. If any of the voltages falls below its threshold, the
MOSFETs are quickly turned off and the voltages are
tracked down together. An internal 100pulldown
resistor ensures that the capacitance at the MOSFET’s
source is discharged quickly. The power-good output
goes low to provide a system reset.
The MAX6880–MAX6883 are available in small 4mm x
4mm 24-pin and 16-pin thin QFN packages and speci-
fied over the -40°C to +85°C extended operating tem-
perature range.
Applications
Multivoltage Systems
Networking Systems
Telecom
Storage Equipment
Servers/Workstations
Features
Capacitor-Adjustable Power-Up Sequencing
Delay
Internal Charge Pumps to Enhance External
n-Channel FETs
Capacitor-Adjustable Timeout Period Power-Good
Output (MAX6880/MAX6882)
Adjustable Undervoltage Lockout or
Logic-Enable Input
Internal 100Pulldown for Each Output to
Discharge Capacitive Load Quickly
0.5V to 5.5V Nominal IN_/OUT_ Range
2.7V to 5.5V Operating Voltage Range
Immune to Short Voltage Transients
Small 4mm x 4mm 24-Pin or 16-Pin Thin QFN
Packages
Ordering Information
PART
TEMP RANGE
MAX6880ETG+ -40°C to +85°C
MAX6881ETE+ -40°C to +85°C
MAX6882ETE+ -40°C to +85°C
MAX6883ETE+ -40°C to +85°C
+Denotes lead-free package.
PIN-
PACKAGE
24 Thin QFN
16 Thin QFN
16 Thin QFN
16 Thin QFN
PKG
CODE
T2444-4
T1644-4
T1644-4
T1644-4
Pin Configurations
TOP VIEW
18 17 16 15 14 13
GATE2 19
12 N.C.
OUT1 20
11 N.C.
GATE1 21
IN3 22
IN2 23
IN1 24
+
12
MAX6880
EP*
34
5
10 TIMEOUT
9 SLEW
8 DELAY
7 GND
6
Selector Guide appears at end of data sheet.
4mm x 4mm THIN QFN
*EXPOSED PADDLE CONNECTED TO GND.
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

line_dark_gray
MAX6881 equivalent
Dual-/Triple-Voltage, Power-Supply
Sequencers/Supervisors
EN/UV
VEN_R
IN_
OUT_
BUS VOLTAGE MONITORED THROUGH EN/UV INPUT
EN/UV
IN1 = 3.3V
IN2 = 1.8V
IN3 = 0.7V
MONITORED THROUGH SET THRESHOLDS ON SET_ INPUTS
CAPACITOR-
ADJUSTED
SLEW RATE
OUT1 = 3.3V
OUT2 = 1.8V
OUT3 = 0.7V
OUT_ FORCED
BELOW VTH_PG
PG/RST
tDELAY
tDELAY
tDELAY
tTIMEOUT
FORCED INTO QUICK SHUTDOWN WHEN OUT1 FALLS BELOW 92.5% of IN1
Figure 3. Sequencing In Fast Shutdown Mode
_______________________________________________________________________________________ 5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MAX6881 electronic component.


Information Total 19 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MAX6881.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MAX688The function is High-Accuracy / Low-Dropout Linear Regulators. Maxim IntegratedMaxim Integrated
MAX688The function is High-Accuracy / Low-Dropout Linear Regulators. Maxim IntegratedMaxim Integrated
MAX6880The function is (MAX6880 - MAX6883) Power-Supply Sequencers/Supervisors. Maxim Integrated ProductsMaxim Integrated Products

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MAX6     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search