DataSheet39.com

What is TSH95I?

This electronic component, produced by the manufacturer "STMicroelectronics", performs the same function as "HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION".


TSH95I Datasheet PDF - STMicroelectronics

Part Number TSH95I
Description HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION
Manufacturers STMicroelectronics 
Logo STMicroelectronics Logo 


There is a preview and TSH95I download ( pdf file ) link at the bottom of this page.





Total 9 Pages



Preview 1 page

No Preview Available ! TSH95I datasheet, circuit

TSH95
HIGH SPEED LOW POWER QUAD OPERATIONAL
AMPLIFIER WITH DUAL STANDBY POSITION
s 2 SEPARATE STANDBY : REDUCED
CONSUMPTION AND HIGH IMPEDANCE
OUTPUTS
s LOW SUPPLY CURRENT : 4.5mA
s HIGH SPEED : 150MHz - 110V/µs
s UNITY GAIN STABILITY
s LOW OFFSET VOLTAGE : 4mV
s LOW NOISE 4.2 nV/Hz
s LOW COST
s SPECIFIED FOR 600AND 150LOADS
s HIGH VIDEO PERFORMANCES :
Differential Gain : 0.03%
Differential Phase : 0.07°
Gain Flatness : 6MHz, 0.1dB max. @ 10dB
gain
s HIGH AUDIO PERFORMANCES
s ESD TOLERANCE : 2kV
DESCRIPTION
The TSH95 is a quad low power high frequency
op-amp, designated for high quality video pro-
cessing. The device offers an excellent speed
consumption ratio with 4.5mA per amplifier for
150MHz bandwidth.
High slew rate and low noise make it also suitable
for high quality audio applications.
The TSH95 offers 2 separate complementary
STANDBY pins :
u STANDBY 1 acting on both n° 1 & 2
operators
u STANDBY 2 acting on both n° 3 & 4
operators
They reduce the consumption of the correspond-
ing operatorS and put the output in a high imped-
ance state.
ORDER CODE
Part Number
TSH95I
Package
Temperature Range
D
-40°C, +125°C
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
D
SO16
(Plastic Micropackage)
PIN CONNECTIONS (top view)
Output 1 1
Inverting Input 1 2
Non-inverting Input 1 3
VCC +
Non-inverting Input 2
4
5
Inverting Input 2 6
Output 2 7
Standby 1 8
-
+
+
-
16 Output 4
- 15 Inverting Input 4
+ 14 Non-inverting Input 4
13 VCC -
+ 12 Non-inverting Input 3
- 11 Inverting Input 3
10 Output 3
9 Standby 2
November 2000
1/9

line_dark_gray
TSH95I equivalent
TSH95
PRINTED CIRCUIT LAYOUT
As for any high frequency device, a few rules must
be observed when designing the PCB to get the
best performances from this high speed op amp.
From the most to the least important points :
u Each power supply lead has to be
by-passed to ground with a 10nF ceramic
capacitor very close to the device and
10µF capacitor.
u To provide low inductance and low resist-
ance common return, use a ground plane
or common point return for power and sig-
nal.
u All leads must be wide and as short as pos-
sible especially for op amp inputs. This is in
order to decrease parasitic capacitance
and inductance.
u Use small resistor values to decrease time
constant with parasitic capacitance.
u Choose component sizes as small as pos-
sible (SMD).
u On output, decrease capacitor load so as
to avoid circuit stability being degraded
which may cause oscillation. You can also
add a serial resistor in order to minimise its
influence.
INPUT OFFSET VOLTAGE DRIFT VERSUS
TEMPERATURE
LARGE SIGNAL FOLLOWER RESPONSE
STATIC OPEN LOOP VOLTAGE GAIN
SMALL SIGNAL FOLLOWER RESPONSE
5/9


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for TSH95I electronic component.


Information Total 9 Pages
Link URL [ Copy URL to Clipboard ]
Download [ TSH95I.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
TSH95The function is HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION. STMicroelectronicsSTMicroelectronics
TSH95IThe function is HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION. STMicroelectronicsSTMicroelectronics
TSH95IDThe function is HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH DUAL STANDBY POSITION. STMicroelectronicsSTMicroelectronics

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

TSH9     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search