DataSheet39.com

What is A54?

This electronic component, produced by the manufacturer "Tyco Electronics", performs the same function as "5 TO 500 MHz CASCADABLE AMPLIFIER".


A54 Datasheet PDF - Tyco Electronics

Part Number A54
Description 5 TO 500 MHz CASCADABLE AMPLIFIER
Manufacturers Tyco Electronics 
Logo Tyco Electronics Logo 


There is a preview and A54 download ( pdf file ) link at the bottom of this page.





Total 10 Pages



Preview 1 page

No Preview Available ! A54 datasheet, circuit

5367
SMOKE DETECTOR
WITH INTERCONNECT AND TIMER
TIMER START 1
I/O 2
LOW-V SET 3
LOGIC
TIMER OUT 4
LED 5
OSC. &
TIMING
+ SUPPLY 6 V DD
TIMING RES. 7
HORN
DRIVER
FEEDBACK 8
16 GUARD 2
15 DETECT. IN
14 GUARD1
13
SENSITIVITY
SET
12 OSC. CAP.
11 HORN 2
10 HORN1
VSS 9 – SUPPLY
Dwg. PC-004
The selectable Hush Feature may be covered
by U.S. patent number Re. 33,920. Any sale or
use of the Hush Feature in a smoke alarm in
the U.S. would be a possible infringement of
this patent.
ABSOLUTE MAXIMUM RATINGS
(Voltages are referenced to VSS)
Supply Voltage Range,
VDD ................................ -0.5 V to +15 V
Reverse Battery (10.5 V) ....................... 20 s
Input Voltage Range,
VIN ........................ -0.3 V to VDD + 0.3 V
Input Current, IIN ............................... 10 mA
Operating Temperature Range,
TA ..................................... 0°C to +50°C
Storage Temperature Range,
TS ............................... -55°C to +125°C
CAUTION: CMOS devices have input static
protection but are susceptible to damage when
exposed to extremely high static electrical
charges.
The A5367CA is a low-current, CMOS circuit providing all of the
required features for an ionization-type smoke detector. A networking
capability allows as many as 125 units to be interconnected so that if
any unit senses smoke, all units will sound an alarm. In addition,
special features are incorporated to facilitate alignment and test of the
finished smoke detector. This device is designed to comply with
Underwriters Laboratories Specification UL217.
The internal oscillator and timing circuitry keeps standby power to
a minimum by powering down the device for 1.66 seconds and sensing
smoke for only 10 ms. Every 24 on/off cycles, a check is made for low
battery condition. By substituting other types of sensors, or a switch
for the ionization detector, this very-low power device can be used in
numerous other battery-operated safety/security applications.
The A5367CA is supplied in a low-cost, 16-pin dual in-line plastic
package. It is rated for continuous operation over the temperature
range of 0°C to +50°C.
FEATURES
s Interconnect Up to 125 Detectors
s Piezoelectric Horn Driver
s Guard Outputs for Detector Input
s Pulse Testing for Low Battery
s Power-ON Reset
s Internal Reverse Battery Protection
s Internal Timer & Control for Reduced Sensitivity
s Built-In Hysteresis Reduces False Triggering
s Temporal Horn Pattern
Always order by complete part number: A5367CA .

line_dark_gray
A54 equivalent
5367
SMOKE DETECTOR
WITH INTERCONNECT
AND TIMER
Sensitivity Adjust. The detector sensitiv-
ity to smoke is set internally by a voltage
divider connected between VDD and VSS. The
sensitivity can be externally adjusted to the
individual characteristics of the ionization
chamber by connecting a resistor between pin
13 and VDD, or between pin 13 and VSS.
Low Battery. The low battery threshold is
set internally by a voltage divider connected
between VDD and VSS. The threshold can be
increased by connecting a resistor between
pin 3 and VDD. The threshold can be de-
creased by connecting a resistor between pin
3 and VSS. The battery voltage level is
checked every 40 seconds during the 10 mA,
10 ms LED pulse. If an LED is not used, it
should be replaced with an equivalent resistor
(typically 500 to 1000 ) such that the
battery loading remains at 10 mA.
Timer. An internal timer is provided that
can be used in various configurations to allow
for a period of reduced smoke detector
sensitivity (“hush”). When a high-to-low
transition occurs at pin 1, the internal timer is
reset, the timer mode enabled, and the circuit
reset to a no alarm condition. The LED will
flash at a 10 second rate. If the level of
smoke is increased such that the reduced
sensitivity level is reached, the device will go
into the alarm condition. The timer, how-
ever, will continue to completion of the
nominal 10-1/4 minute period (368 clock
cycles). If the timer mode is not used, pin 1
should be tied low.
I/O. A connection is provided at pin 2 to
allow multiple smoke detectors to be
commoned. If any single unit detects smoke
(I/O is driven high), all connected units will
sound their associated horns after a nominal 3
second delay. The LED is suppressed when
an alarm is signaled from an interconnected
TYPICAL APPLICATION
9V
TIMER
MODE
200 k
TO
OTHER
UNITS
200
1
2
NOTE
3
330
3
4
5
LOGIC
OSC. &
TIMING
8.2 M
6 V DD
7
HORN
DRIVER
1 µF
8
16
15
14
13
12
11
10
V SS 9
0.1 µF
PUSH
TO
TEST
NOTE
1
NOTE 2
0.001 µF
Dwg. EC-005A
NOTE 1: Use an external resistor to adjust sensitivity for a particular smoke
chamber.
NOTE 2: Select resistor to reduce sensitivity during timer mode.
NOTE 3: A resistor to ground or V may be added to this pin to modify low
DD
battery voltage threshold.
unit. An internal NMOS device acts as a charge dump to aid in appli-
cations involving a large (distributed) capacitance on pin 2. The
charge dump is activated only on the removal of a local alarm.
Testing. On power up, all internal counters are reset. Internal test
circuitry allows for low battery check by holding pins 8 and 12 low
during power up, then reducing VDD and monitoring HORN1 (pin 10).
All functional tests can be accelerated by driving pin 12 with a 2 kHz
square wave. The 10 ms strobe period must be maintained for proper
operation of the comparator circuitry.
www.allegromicro.com
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for A54 electronic component.


Information Total 10 Pages
Link URL [ Copy URL to Clipboard ]
Download [ A54.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
A5-5The function is Cascadable Amplifier. MA-COMMA-COM
A500The function is SILICON RECTIFIER. Powerex Power SemiconductorsPowerex Power Semiconductors
A500K130The function is ProASIC 500K Family. Actel CorpActel Corp

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

A54     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search