DataSheet39.com

What is GS6042?

This electronic component, produced by the manufacturer "Semtech", performs the same function as "6G UHD-SDI/3G/HD/SD Adaptive Cable Equalizer".


GS6042 Datasheet PDF - Semtech

Part Number GS6042
Description 6G UHD-SDI/3G/HD/SD Adaptive Cable Equalizer
Manufacturers Semtech 
Logo Semtech Logo 


There is a preview and GS6042 download ( pdf file ) link at the bottom of this page.





Total 21 Pages



Preview 1 page

No Preview Available ! GS6042 datasheet, circuit

Gennum Products
GS6042
6G UHD-SDI/3G/HD/SD Adaptive
Cable Equalizer
Key Features
Supports data rates from 125Mb/s to 6.25Gb/s
SMPTE ST 2081 (proposed), SMPTE ST 424,
SMPTE ST 292, and SMPTE ST 259 compliant
Automatic cable equalization
Typical equalized length of Belden 1694A cable:
Š 80m at 5.94Gb/s
Š 210m at 2.97Gb/s
Š 300m at 1.485Gb/s
Š 500m at 270Mb/s
Supports DVB-ASI at 270Mb/s
Supports MADI at 125Mb/s
Manual bypass control
Programmable carrier detect with squelch threshold
adjustment
Automatic power-down on loss of signal
Differential output supports DC-coupling from +1.2V
to +3.3V CML logic
Optional 6dB flat band gain on input
Selectable output de-emphasis: 2dB, 6dB, and 8dB
Standard EIA/JEDEC logic for control/status signals
Single +3.3V power supply operation
180mW power consumption (35mW in sleep)
Operating temperature range: -40ºC to +85ºC
Small footprint QFN package (4mm x 4mm)
Š Footprint compatible with the GS2974A, GS2974B,
GS2984, GS2994, and GS3440
Pb-free and RoHS compliant
Applications
SMPTE ST 2081 (proposed), SMPTE ST 424,
SMPTE ST 292, and SMPTE ST 259 coaxial cable serial
digital interfaces
Serialized 8b/10b encoded video streams up to
6.25Gb/s
Description
The GS6042 is a high-speed BiCMOS device designed to
optimally equalize and restore signals received over 75Ω
coaxial cable.
The device supports data rates up to 6.25Gb/s while being
optimized for the proposed SMPTE ST 2081, as well as
SMPTE ST 424, SMPTE ST 292, and SMPTE ST 259.
The GS6042 features DC restoration to compensate for the
DC content of SMPTE pathological signals.
The Carrier Detect output pin (CD) indicates whether an
input signal has been detected. It can be connected
directly to the SLEEP pin to enable automatic sleep on loss
of input.
A CD threshold is set via the SQ_ADJ pin, allowing the
GS6042 to distinguish between small amplitude SDI signals
and noise at the input of the device.
The equalizing and DC restore stages are disengaged and
no equalization occurs when the BYPASS pin is HIGH. This is
useful for signals launched at the signal source with low
data rates and/or slow rise/fall times.
The GS6042 features a gain selection pin (GAIN_SEL) which
can be used to compensate for 6dB flat attenuation prior to
the input of the device.
The differential output can be DC-coupled to Semtech’s
reclockers and cable drivers, as well as industry-standard
CML logic by changing the voltage applied to the
VCC_O pin. In general, DC-coupling to any termination
voltage between +1.2V and +3.3V is supported.
The GS6042 also features programmable output
de-emphasis with three user-selectable operating levels to
support long PCB traces at the output of the device.
Power consumption of the GS6042 is typically 180mW
when its output is DC-coupled at +1.2V.
The GS6042 is Pb-free, and the encapsulation compound
does not contain halogenated flame retardant. This
component and all homogeneous subcomponents are
RoHS compliant.
GS6042
Final Data Sheet
PDS-060055
Rev. 3
May 2014
www.semtech.com
1 of 21
Proprietary and Confidential

line_dark_gray
GS6042 equivalent
Table 1-1: GS6042 Pin Descriptions (Continued)
Pin Number Name
8 SQ_ADJ
9 OP_CTL
10, 11
12
13
DDO, DDO
VEE_O
VCC_O
14 SLEEP
15 CD
16 VCC_A
— Center Pad
Type
Input
Input
Output
Power
Power
Input
Output
Power
Power
Description
Squelch Threshold Adjust.
Adjusts the input signal amplitude threshold of the carrier detect
function. The serial data output of the device can be muted when
the serial data input signal amplitude is too low by connecting the
CD and OP_CTL pins using a suitable resistor network (see
Figure 4-4 and Figure 4-5).
This pin has an internal pull-down resistor.
Note: The SQ_ADJ function is only available when the device is not
configured for auto-sleep mode. Reference Section 4.5 for more
detail.
Output Swing, De-emphasis and Mute Control.
When this pin is connected to GND, the output swing is 850mVppd
with no de-emphasis applied to the output signal.
With this pin connected to +2.5V, the output is muted.
Intermediate voltages and functions are shown in Table 4-5. These
voltages can be achieved as shown in Figure 4-4 and Figure 4-5.
This pin has an internal pull-down resistor.
Serial digital differential output.
Most negative power supply connection for the output buffer.
Connect to ground.
Most positive power supply connection for the output buffer.
Connect to 1.2V - 3.3V DC.
SLEEP Control.
Please refer to the DC Electrical Characteristics table for logic level
threshold and compatibility. This pin is a +2.5V input that is tolerant
to +3.3V levels.
When HIGH the part is powered-down except for the Carrier Detect
function.
This pin can be connected directly to the CD pin to automatically
put the device to sleep (low-power operation) on loss of carrier.
This pin has an internal pull-down resistor.
Note: When SLEEP is connected to CD for automatic power
reduction on loss of carrier, the SQ_ADJ pin will not modify the CD
threshold. The CD threshold will revert to the default value used
when SQ_ADJ is pulled LOW.
Carrier Detect Status Output.
Please refer to the DC Electrical Characteristics table for logic level
threshold and compatibility. This pin is a +2.5V output.
Indicates presence of an input signal. When the CD pin is LOW, a
signal has been detected at the input. When this pin is HIGH, this
indicates loss of input signal.
Most positive power supply connection for the input buffer, core
and control circuits.
Connect to +3.3V DC.
Internally bonded to VEE_A.
Connect to GND with at least 5 vias.
GS6042
Final Data Sheet
PDS-060055
Rev. 3
May 2014
www.semtech.com
5 of 21
Proprietary and Confidential


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for GS6042 electronic component.


Information Total 21 Pages
Link URL [ Copy URL to Clipboard ]
Download [ GS6042.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
GS6042The function is 6G UHD-SDI/3G/HD/SD Adaptive Cable Equalizer. SemtechSemtech

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

GS60     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search