DataSheet39.com

What is GS2994?

This electronic component, produced by the manufacturer "Semtech", performs the same function as "Adaptive Cable Equalizer".


GS2994 Datasheet PDF - Semtech

Part Number GS2994
Description Adaptive Cable Equalizer
Manufacturers Semtech 
Logo Semtech Logo 


There is a preview and GS2994 download ( pdf file ) link at the bottom of this page.





Total 20 Pages



Preview 1 page

No Preview Available ! GS2994 datasheet, circuit

GS2994
GS2994 Adaptive Cable Equalizer
Key Features
• SMPTE 424M, SMPTE 292M and SMPTE 259M
compliant
• Automatic cable equalization
• Multi-standard operation from 143Mb/s to 2.97Gb/s
• Performance optimized for 270Mb/s, 1.485Gb/s and
2.97Gb/s. Typical equalized length of Belden 1694A
cable:
Š 140m at 2.97Gb/s
Š 220m at 1.485Gb/s
Š 400m at 270Mb/s
• Supports DVB-ASI at 270Mb/s
• Manual bypass (useful for low data rates with slow
rise/fall times)
• Programmable carrier detect with squelch threshold
adjustment
• Automatic power-down on loss of signal
Š Standby power <30mW (typical)
• Differential outputs support DC-coupling to 1.2V, 2.5V
and 3.3V CML logic
• 0/6 dB gain boost selection pin
• Selectable de-emphasis: 2dB, 4dB and 6dB
• Standard EIA/JEDEC logic control and status signal
levels
• Single 3.3V power supply operation
• 167mW power consumption (typical)
• Wide operating temperature range of -40ºC to +85ºC
• Small footprint QFN package (4mm x 4mm)
Š Footprint compatible with the GS2974 and the
GS2984
• Pb-free and RoHS compliant
Applications
• SMPTE 424M, SMPTE 292M and SMPTE 259M coaxial
cable serial digital interfaces
Description
The GS2994 is a high-speed BiCMOS integrated circuit
designed to equalize and restore signals received over 75Ω
coaxial cable.
The device is designed to support SMPTE 424M,
SMPTE292M and SMPTE 259M, and is optimized for
performance at 270Mb/s, 1.485Gb/s and 2.97Gb/s.
The GS2994 features DC restoration to compensate for the
DC content of SMPTE pathological test patterns.
The Carrier Detect output pin (CD) indicates whether a
valid input signal has been detected. It can be connected
directly to the SLEEP pin to enable automatic power-down
upon loss of carrier. In the manual sleep mode, a voltage
programmable threshold, which can be changed via the
SQ_ADJ pin, forces CD high when the input signal
amplitude falls below the threshold. This allows the GS2994
to distinguish between low-amplitude SDI signals and
noise at the input of the device.
The equalizing and DC restore stages are disengaged when
the BYPASS pin is HIGH. No equalization occurs in Bypass
mode.
The GS2994 includes a gain selection pin (GAIN_SEL)
which, when tied HIGH, compensates for 6dB flat
attenuation.
The differential outputs can be DC-coupled to Gennum
3.3V cable drivers and reclockers and to industry-standard
1.2V, 2.5V and 3.3V CML logic using the VCC_O pin. In
general, DC-coupling to any termination voltage between
1.2V and 3.3V is supported.
The GS2994 also includes programmable de-emphasis with
three operating levels in order to support long PCB traces.
The GS2994 is footprint and drop-in compatible with
existing GS2974 and GS2984 designs.
The device is available in a 16-pin, 4mm x 4mm QFN
package.
Power consumption of the GS2994 is typically 167mW
when DC-coupled at 1.2V.
The GS2994 is Pb-free, and the encapsulation compound
does not contain halogenated flame retardant.
This component and all homogeneous subcomponents are
RoHS compliant.
GS2994 GS2994 Adaptive Cable Equalizer
Data Sheet
53967 - 4
August 2012
www.semtech.com
1 of 20

line_dark_gray
GS2994 equivalent
Table 1-1: GS2994 Pin Descriptions (Continued)
Pin Number
8
Name
SQ_ADJ
Timing
Analog
Type
Input
9
OP_CTL
Not
Input
Synchronous
10, 11
12
13
SDO, SDO
VEE_O
VCC_O
Analog
Analog
Analog
Output
Power
Power
14 SLEEP Not Input
Synchronous
15 CD Not Output
Synchronous
16
VCC_A
Analog
Power
Center Pad
Power
Description
Squelch Threshold Adjust.
Adjusts the input signal amplitude threshold of the carrier detect
function. The output can be muted when the input signal
amplitude is too low by connecting the CD and OP_CTL pins
together through some external components. In this case, when CD
is LOW (0V), OP_CTL is forced LOW (0V), and when CD is HIGH
(2.5V), OP_CTL is forced HIGH (3.3V). The input level at which the
part is muted can be set through the SQ_ADJ pin through suitable
voltage variances as described in Section 4.4. NOTE: when the
SQ_ADJ functionality is used and/or in auto_mute, the auto sleep
feature is not allowed, and the SLEEP pin should be left open.
Includes an internal pull-down resistor.
CONTROL SIGNAL INPUT
Controls the Output Swing, De-emphasis, and Mute features of the
SDO and SDO outputs.
When connected to GND, the output swing is 800mV with no
de-emphasis. When connected to the 3.3V analog power supply, the
output is MUTED.
Includes an internal pull down resistor.
See Section 4.7 for all other control options.
Equalized serial digital differential output.
Most negative power supply for the output buffer.
Connect to GND.
Most positive power supply connection for the output buffer of the
device.
Connect to +1.2V ~ +3.3V DC.
CONTROL SIGNAL INPUT
When set HIGH, the GS2994 is powered-down except for the Carrier
Detect functionality.
Includes an internal pull-down resistor.
Carrier Detect status signal output.
Signal levels are LVCMOS/LVTTL compatible.
Indicates the presence of an input signal. When the CD pin is LOW, a
good input signal has been detected. When this pin is HIGH, the
input signal is invalid.
See Section 4.5.
Most positive power supply for the input buffer, core and control
circuits of the device.
Connect to +3.3V DC.
Internally bonded to VEE_A.
GS2994 GS2994 Adaptive Cable Equalizer
Data Sheet
53967 - 4
August 2012
5 of 20


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for GS2994 electronic component.


Information Total 20 Pages
Link URL [ Copy URL to Clipboard ]
Download [ GS2994.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
GS2993The function is Dual Output Adaptive Cable Equalizer. SemtechSemtech
GS2994The function is Adaptive Cable Equalizer. SemtechSemtech

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

GS29     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search