DataSheet39.com

What is MB95F283H?

This electronic component, produced by the manufacturer "Fujitsu Media Devices", performs the same function as "8-bit Microcontrollers".


MB95F283H Datasheet PDF - Fujitsu Media Devices

Part Number MB95F283H
Description 8-bit Microcontrollers
Manufacturers Fujitsu Media Devices 
Logo Fujitsu Media Devices Logo 


There is a preview and MB95F283H download ( pdf file ) link at the bottom of this page.





Total 30 Pages



Preview 1 page

No Preview Available ! MB95F283H datasheet, circuit

FUJITSU MICROELECTRONICS
DATA SHEET
DS07–12627–1E
8-bit Microcontrollers
CMOS
F2MC-8FX MB95260H/270H/280H Series
MB95F262H/F262K/F263H/F263K/F264H/F264K
MB95F272H/F272K/F273H/F273K/F274H/F274K
MB95F282H/F282K/F283H/F283K/F284H/F284K
DESCRIPTION
MB95260H/270H/280H are series of general-purpose, single-chip microcontrollers. In addition to a compact
instruction set, the microcontrollers of these series contain a variety of peripheral resources.
Note: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
FEATURES
• F2MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instructions
• Bit manipulation instructions, etc.
• Clock (main OSC clock and sub-OSC clock are only available in MB95F262H/F262K/F263H/F263K/F264H/
F264K/F282H/F282K/F283H/F283K/F284H/F284K)
• Selectable main clock source
Main OSC clock (up to 16.25 MHz, maximum machine clock frequency: 8.125 MHz)
External clock (up to 32.5 MHz, maximum machine clock frequency: 16.25 MHz)
Main internal CR clock (1/8/10 MHz ±3%, maximum machine clock frequency: 10 MHz)
• Selectable subclock source
Sub-OSC clock (32.768 kHz)
External clock (32.768 kHz)
Sub-internal CR clock (Typ: 100 kHz, Min: 50 kHz, Max: 200 kHz)
• Timer
• 8/16-bit composite timer
• Timebase timer
• Watch prescaler
• LIN-UART (MB95F262H/F262K/F263H/F263K/F264H/F264K/F282H/F282K/F283H/F283K/F284H/F284K)
• Full duplex double buffer
• Capable of clock-synchronized serial data transfer and clock-asynchronized serial data transfer
(Continued)
Copyright©2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2008.12

line_dark_gray
MB95F283H equivalent
MB95260H/270H/280H Series
• MB95270H Series
Part number
MB95F272H MB95F273H MB95F274H MB95F272K MB95F273K MB95F274K
Parameter
Type
Flash memory product
Clock
supervisor
counter
It supervises the main clock oscillation.
Program ROM
capacity
8 Kbytes
12 Kbytes 20 Kbytes
8 Kbytes
12 Kbytes 20 Kbytes
RAM capacity 240 bytes 496 bytes 496 bytes 240 bytes 496 bytes 496 bytes
Low-voltage
detection reset
No
Yes
Reset input
Dedicated
Selected by software
Number of basic instructions
: 136
Instruction bit length
: 8 bits
CPU functions
Instruction length
Data bit length
: 1 to 3 bytes
: 1, 8 and 16 bits
Minimum instruction execution time : 61.5 ns (with machine clock = 16.25 MHz)
Interrupt processing time
: 0.6 µs (with machine clock = 16.25 MHz)
General-
purpose I/O
I/O ports (Max): 4
CMOS: 3
N-ch: 1
I/O ports (Max): 5
CMOS: 3
N-ch: 2
Timebase timer Interrupt cycle : 0.256 ms to 8.3 s (when external clock = 4 MHz)
Hardware/ Reset generation cycle
software
Main oscillation clock at 10 MHz: 105 ms (Min)
watchdog timer The sub-internal CR clock can be used as the source clock of the hardware watchdog timer.
Wild register It can be used to replace three bytes of data.
LIN-UART No LIN-UART
8/10-bit A/D 2 channels
converter
8-bit or 10-bit resolution can be selected.
1 channel
8/16-bit
composite
timer
The timer can be configured as an "8-bit timer × 2 channels" or a "16-bit timer × 1 channel".
It has built-in timer function, PWC function, PWM function and input capture function.
Count clock: it can be selected from internal clocks (seven types) and external clocks.
It can output square wave.
External
interrupt
2 channels
Interrupt by edge detection (The rising edge, falling edge, or both edges can be selected.)
It can be used to wake up the device from standby modes.
On-chip debug
1-wire serial control
It supports serial writing. (asynchronous mode)
Watch
prescaler
Eight different time intervals can be selected.
It supports automatic programming, Embedded Algorithm,
write/erase/erase-suspend/erase-resume commands.
Flash memory
It has a flag indicating the completion of the operation of Embedded Algorithm.
Number of write/erase cycles (Min): 100000
Data retention time: 20 years
Flash security feature for protecting the content of the Flash memory
Standby mode Sleep mode, stop mode, watch mode, timebase timer mode
Package
DIP-8P-M03
FPT-8P-M08
DS07–12627–1E
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MB95F283H electronic component.


Information Total 30 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MB95F283H.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MB95F283HThe function is 8-bit Microcontrollers. Fujitsu Media DevicesFujitsu Media Devices
MB95F283KThe function is 8-bit Microcontrollers. Fujitsu Media DevicesFujitsu Media Devices

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MB95     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search