GRM42-6X5R475K010 Datasheet PDF - AUK corp
Part Number | GRM42-6X5R475K010 | |
Description | Low Drop Output Voltage Regulator | |
Manufacturers | AUK corp | |
Logo | ||
There is a preview and GRM42-6X5R475K010 download ( pdf file ) link at the bottom of this page. Total 6 Pages |
Preview 1 page No Preview Available ! Semiconductor
S52xxM
Low Drop Output Voltage Regulator
Description
The S52xxM is a u-cap 150mA linear voltage regulator in the SOT-25 package. This
regulator has very low dropout voltage and very low ground current. It is designed
especially for hand-sets, battery-powered devices and can be controlled by a CMOS or TTL.
When the S52xxM is disabled, power consumption drops to nearly zero.
Features
• Low dropout voltage regulator
• Low quiescent current and guaranteed 150mA output
• Zero off-mode current
Ordering Information
Type NO.
Marking
Package Code
S52xxM
5□□
□□: Voltage Code
SOT - 25
Outline Dimensions
unit : mm
BLOCK DIAGRAM
PIN Connections
1. Supply Input
2. Ground
3. Enable/Shutdown
4. Noise Bypass
5. Regulator Output
KSI-2012-006
1
|
|
Electrical Characteristic Curves (Cont.)
Fig. 7.
Fig. 8
S52xxM
Shutdown (Dis/Enable) Operation
The S52xxM output can be turned off by applying 0.4V or less to the device’s Dis/Enable
pin (pin3). In shutdown mode, the S52xxM draws less than 1uA quiescent current. The
output of the S52xxM is enabled by applying 1.5V to 13V at the Dis/Enable pin. In
applications were the S52xxM output will always remain enabled, the Dis/Enable pin may
be connected to Vin(pin1). The S52xxM’s shutdown circuitry includes hysteresis, as such
the device will operate properly even if a slow moving signal is applied to the Dis/Enable
pin. The device’s shutdown pin includes a 2MΩ internal pull down resistor connected to
ground.
Short Circuit Protection
The S52xxM output can withstand momentary short circuit to ground. Moreover, the
regulator can deliver very high output peak current due to its 1A instantaneous short circuit
current capability.
Noise Bypass Capacitor
In low noise applications, the self noise of the S52xxM can be decreased further by
connecting a capacitor from the noise bypass pin (pin4) to ground (pin2). The noise bypass
pin is a high impedance node as such care should be taken in printed circuit board layout to
avoid noise pick-up from external sources. Moreover, the noise bypass capacitor should
have low leakage. Noise bypass capacitors with a value as low as 470pF may be used.
However, for optimum performance, use a 0.01uF or larger, ceramic chip capacitor. Note
that the turn on and turn off response of the S52xxM is inversely proportional to the value
of the noise bypass capacitor. For fast turn on and turn off, use a small value noise Bypass
capacitor. In applications were exceptionally low output noise is not required, consider
omitting the noise Bypass capacitor altogether.
KSI-2012-006
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for GRM42-6X5R475K010 electronic component. |
Information | Total 6 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ GRM42-6X5R475K010.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
GRM42-6X5R475K010 | The function is Low Drop Output Voltage Regulator. AUK corp | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
GRM4
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |