GP1U26R Datasheet PDF - Sharp Electrionic Components
Part Number | GP1U26R | |
Description | Anti Electromagnetic Induction Noise Type Compact IR Detecting Unit for Remote Control | |
Manufacturers | Sharp Electrionic Components | |
Logo | ||
There is a preview and GP1U26R download ( pdf file ) link at the bottom of this page. Total 5 Pages |
Preview 1 page No Preview Available ! GP1U26R/27R/28R/28Q Series
GP1U26R/GP1U27R Series
GP1U28R/GP1U28Q Series
Anti Electromagnetic Induction
Noise Type Compact IR Detecting
Unit for Remote Control
s Features
1. Anti electromagnetic induction noise type
2. Compact (case volume)
(GP1U28Q : About 1/4 compared with GP1U78Q)
3. Power filter capacitor and resistance are not required any more
as a result of adoption of built-in constant voltage circuit
4. Various B.P.F. (Band Pass Frequency) frequency to meet different user needs
s Applications
1. AV equipment such as TV sets,
VCRs and audio equipment
2. HA equipment such as air conditioners
and electric fans
s Outline Dimensions
GP1U26R Series
7.3
0.5
2 5.2 3.6
GP1U27R Series
7.3
0.5
(Unit : mm)
2 10.4 3.6
Φ 4.5
Marking
Φ 4.5
Marking
*1
2.54
*1
2.54
4
Recommended drilling as viewed from the soldering face.
3.75 3.75
1.2
*1
2.54
*1
2.54
4
Recommended drilling as viewed from the soldering face.
3.75 3.75
1.2
2-0.5
2-0.4
2-0.75
0.6 1 2 3
2-0.75
1 Vout
2 VCC
3 GND
0.6
1.2
Detector
center
(0.5)
Φ 0.8
2.54
2.54
1. Unspecified tolerance : ± 0.3
GP1U28R Series
7.3
0.5
2
2. * 1 : The dimension of lead base
14.4 3.6
2-0.5
2-0.4
2-0.75
1
0.6
23
2-0.75
1 Vout
2 VCC
3 GND
0.6
1.2
Detector
center
(0.5)
Φ 0.8
2.54 2.54
1. Unspecified tolerance : ± 0.3
GP1U28Q Series
7.3
0.5
2. * 1 : The dimension of lead base
24
Φ 4.5
Marking
Marking
*1
2.54
*1
2.54
4
Recommended drilling as viewed from the soldering face.
3.75 3.75
1.2
1.2
2-0.5
2-0.4
2-0.75
1 Vout
2 VCC
3 GND
0.6 1
23
2-0.75
0.6
Detector
center
(0.5)
Φ 0.8
2.54 2.54
1. Unspecified tolerance : ± 0.3 2. * 1 : The dimension of lead base
0.4
0.6 1 2 3 0.6
1.6
3.7
1.4
1.4
5.4
1 Vout
6.8
2 VCC Recommended drilling as viewed from the soldering face.
3 GND
2.54 2.54
0.5
*1
2.54
*1
2.54
1. Unspecified tolerance : ± 0.3
1.2 1.2
3.75 3.75
2. * 1 : The dimension of lead base
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”
|
|
Fig. 5 AEHA (Japan Association of Electrical Home Appliances)
Code Pulse Width Characteristics (1st Bit) [TYP.] for Reference
700
Low level pulse width
600
500
400
300
High level pulse width
200
Unit AEHA code
100
generating transmitter
1st bit
VCC =5V, Ta=RT, φ =0˚,
Ee < 10 lx, T=430µ s
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Reception distance (m)
GP1U26R/27R/28R/28Q Series
Fig. 6 Spectral Sensitivity for Reference
100
90
80
70
60
50
40
30
20
10
700 800 900 1000 1100 1200
Wavelength λ (nm)
s Precautions for Operation
1) In case of adopting the infrared light detecting unit for the wireless remote control, use it in accordance
with the transmission scheme and the signal format recommended in "Countermeasures for malfunction prevention of
home appliances with remote control" issued from Japan Association of Electrical Home Appliances (AEHA) in July, 1987.
Use of a transmission scheme and a signal format different from those recommended may cause malfunction of home appliances.
(Example : signal format without leader signal, bit structure of small duty ratio (TH/(TH+T L)))
2) Use the light emitting unit (remote control transmitter), in consideration of performance, characteristics,
operating conditions of light light emitting device and the characteristics of the light detecting unit.
3) Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse.
Care must be taken not to touch the light detector surface.
If it should be dirty, wipe off such dust and refuse with soft cloth so as to prevent scratch. In case some solvents are required,
use methyl alcohol, ethyl alcohol or isopropyl alcohol only.
Also, protect the light detecting unit against flux and others, since their deposition on the unit inside causes reduction of the function,
fading of markings such as the part number.
4) The shield case should be grounded on PWB pattern.
(The area across the shield case and the GND terminal is internally conductive in some cases and non-conductive in some other cases.)
5) Do not apply unnecessary force to the terminal and the case.
6) Do not push the light detector surface (photodiode) from outside.
7) To avoid the electrostatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc.
8) Do not use hole and groove set in the case of the light detecting unit for other purposes,
since they are required to maintain the specified performance.
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for GP1U26R electronic component. |
Information | Total 5 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ GP1U26R.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
GP1U26R | The function is Anti Electromagnetic Induction Noise Type Compact IR Detecting Unit for Remote Control. Sharp Electrionic Components | |
GP1U26X | The function is Compact IR Detecting Unit for Remote Control. Sharp Electrionic Components | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
GP1U
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |