DataSheet39.com

What is PCK0E561MCO1GS?

This electronic component, produced by the manufacturer "Nichicon", performs the same function as "CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS".


PCK0E561MCO1GS Datasheet PDF - Nichicon

Part Number PCK0E561MCO1GS
Description CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Manufacturers Nichicon 
Logo Nichicon Logo 


There is a preview and PCK0E561MCO1GS download ( pdf file ) link at the bottom of this page.





Total 2 Pages



Preview 1 page

No Preview Available ! PCK0E561MCO1GS datasheet, circuit

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CK Chip Type, Ultra-low ESR
series
Ultra-low ESR, Higher Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Compliant to the RoHS directive (2002/95/EC).
CJ
Low ESR
CK
Specifications
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 6.3V
Rated Capacitance Range 220 to 2200µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
Marking
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
Type numbering system (Example : 6.3V 220µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PCK 0 J 2 2 1 MCO 1 GS
Series
Voltage ( j:6.3v)
L
+0.1
- 0.4
Negative
H
(mm)
Size φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L
φD 6.3
8.0 10.0 10.0
L 5.9 6.9 7.9 9.9
A 7.3
9.0 11.0 11.0
B 6.6
8.3 10.3 10.3 Voltage
C 6.6
8.3 10.3 10.3
E 2.1 3.2 4.6 4.6
H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
V 2.5 4 6.3
Code e g
j
Taping code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (220µF)
Rated voltage (6.3V)
Series name
Type
Dimension table in next page.
CAT.8100Z


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for PCK0E561MCO1GS electronic component.


Information Total 2 Pages
Link URL [ Copy URL to Clipboard ]
Download [ PCK0E561MCO1GS.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
PCK0E561MCO1GSThe function is CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS. NichiconNichicon

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

PCK0     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search