|
|
PDF KT0806L Data sheet ( Hoja de datos )
| Número de pieza | KT0806L | |
| Descripción | Monolithic Digital Stereo FM Transmitter | |
| Fabricantes | KTMicro | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de KT0806L (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
|
No Preview Available !
Monolithic Digital Stereo FM Transmitter
Radio-Station-on-a-Chip™
KT0806L
Features
Hardware compatible with KT0806
Additional features to KT0806
Software standby;
Automatic power down power amplifier
when silence is detected;
Multiple reference clock support
including from 32.768KHz to 26MHz;
ALC (Automatic Level Control)
Higher SNR (66dB)
Increased audio frequency response
Software controlled XTAL selection
Professional Grade Performance:
SNR ≥ 66 dB
Stereo Separation > 40 dB
International compatible 70MHz ~ 108MHz
Ultra-Low Power Consumption:
< 17 mA operation current
< 3 µA standby current
Small Form Factor:
16-pins QFN 3x3
Simple Interface:
Single power supply
Standard 2-wire I2C MCU interface
Advanced Digital Audio Signal Processing:
On-chip 20-bit ΔΣ Audio ADC
On-chip DSP core
On-chip 24dB PGA with optional 1dB step
Automatic calibration against process
and temperature
1.6V ~ 3.6V supply
Programmable transmit level
Programmable pre-emphasis (50/75 µs)
Pb-free and RoHS Compliant
Applications
MP3 Player, Cellular Phone, PDA, PND,
Portable Personal Media player and its accessory,
Laptop Computer, Wireless Speaker
Rev. 1.4
Information furnished by KT Micro is believed to be accurate
and reliable. However, no responsibility is assumed by KT
Micro for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any
patent or patent rights of KT Micro, Inc..
Figure 1: KT0806L System Diagram
General Description
KT0806L, our new generation of low cost Monolithic
Digital FM Transmitter, is designed to process high-fidelity
stereo audio signal and transmit modulated FM signal over
a short range. It’s based on the architecture of award-
winning KT0801 and it’s also an upgrade of KT0806. The
additional features added to KT0806L are standby mode
through software, ALC (automatic level control), multiple
reference clock, increased SNR performance and frequency
response.
The KT0806L features dual 20-bit ΔΣ audio ADCs, a high-
fidelity digital stereo audio processor and a fully integrated
radio frequency (RF) transmitter. An on-chip low-drop-out
regulator (LDO) allows the chip to be integrated in a wide
range of low-voltage battery-operated systems with power
supply ranging from 1.6V to 3.6V.
The KT0806L is configured as an I2C slave and
programmed through the industry standard 2-wire MCU
interface.
Thanks to its high integration level, the KT0806L is
mounted in a generic 16-pin QFN package. It only requires
a single low-voltage supply. No external tuning is required
that makes design-in effort minimum.
KT Micro, Inc., 22391 Gilberto, Suite D
Rancho Santa Margarita, CA 92688
Tel: 949.713.4000 http://www.ktmicro.com
Fax: 949.713.4004 Copyright ©2010, KT Micro, Inc..
1 page  
KT0806L
CURRENT ADDRESS READ: The internal data register address counter maintains the last address
accessed during the last read or write operation, incremented by one. This address stays valid between
operations as long as the chip power is maintained.
Once the device address with the read/write select bit set to “1” is clocked in and acknowledged by the
KT0806L, the current address data word is serially clocked out. The microcontroller does not respond with
an input “0” but does generate a following stop condition (see Figure 4).
CURRENT REGISTER READ PROCEDURE
S 0 1 1 0 1 1 0 RA
7 bit address
data
Acknowledge
START condition READ command
AP
STOP condition
NO Acknowledge
Figure 4: Serial Interface Protocol
Note: The serial controller supports slave mode only. Any register can be addressed randomly.
The address of the slave in the first 7 bits and the 8th bit tells whether the master is receiving data from the
slave or transmitting data to the slave. The I2C write address is 0x6C and the read address is 0x6D.
4.2 Slave Mode Protocol
With reference to the clocking scheme shown in Figure 5, the serial interface operates in the following
manner:
Figure 5: Serial Interface Slave Mode Protocol
CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data
on the SDA pin may change only during SCL low time periods (see Figure 6). Data changes during SCL
high periods will indicate a start or stop condition as defined below.
START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must
precede any other command (see Figure 7).
STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read
sequence, the stop command will place the KT0806L in a standby power mode (see Figure 7).
ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the KT0806L in 8-
bit words. The KT0806L sends a “0” to acknowledge that it has received each word. This happens during
the ninth clock cycle (see Figure 8).
Copyright ©2010, KT Micro, Inc.
5
5 Page 
KT0806L
Bits Type Default Label
Description
3:0 RW 0000 ALC_ATTACK_TIM ALC Attack Time Selection
E[3:0]
0000 = 25us
0001 = 50us
0010 = 75us
0011 = 100us
0100 = 125us
0101 = 150us
0110 = 175us
0111 = 200us
1000 = 50ms
1001 = 100ms
1010 = 150ms
1011 = 200ms
1100 = 250ms
1101 = 300ms
1110 = 350ms
1111 = 400ms
5.7 Register 0x0E (Address: 0x0E, Default: 0x02)
Bit 7 6 5 4 3
KT0806L
-
-
-
-
-
21
- PA_BIAS
Bits Type Default Label
7:2 RW 0x00 Reserved
1 RW 1
PA_BIAS
0 RW 0
Reserved
Description
Reserved
PA Bias Current Enhancement.
0 = Disable
1 = Enable
Reserved
0
-
5.8 Register 0x0F (Address: 0x0F, Read only)
Bit 7 6 5
4
KT0806L
-
-
- PW_OK
3
-
2
SLNCID
Bits Type Default Label
7 R NA Reserved
6 R NA Reserved
5 R NA Reserved
4 R NA PW_OK
3 R NA Reserved
2 R NA SLNCID
1 R NA Reserved
0 R NA Reserved
Description
Reserved
Reserved
Reserved
Power OK Indicator
Reserved
1 When Silence is Detected
Reserved
Reserved
1
-
0
-
5.9 Register 0x10 (Address: 0x10, Default: 0xA8)
Bit 7 6 5
KT0806L
-
-
-
KT0806
-
-
-
43
--
LMTLVL[1:0]
21
0
- - PGAMOD
- - PGAMOD
Copyright ©2010, KT Micro, Inc.
11
11 Page | ||
| Páginas | Total 23 Páginas | |
| PDF Descargar | [ Datasheet KT0806L.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| KT0806L | Monolithic Digital Stereo FM Transmitter | KTMicro |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |