DataSheet39.com

What is RF5605?

This electronic component, produced by the manufacturer "RFMD", performs the same function as "2.4GHz TO 2.5GHz HIGH POWER FRONT END MODULE".


RF5605 Datasheet PDF - RFMD

Part Number RF5605
Description 2.4GHz TO 2.5GHz HIGH POWER FRONT END MODULE
Manufacturers RFMD 
Logo RFMD Logo 


There is a preview and RF5605 download ( pdf file ) link at the bottom of this page.





Total 17 Pages



Preview 1 page

No Preview Available ! RF5605 datasheet, circuit

RF56055.0 V,
2.4GHz TO
2.5GHz HIGH
POWER FRONT
END MODULE
RF5605
5.0V, 2.4GHz TO 2.5GHz HIGH POWER
FRONT END MODULE
Package: 6mmx6mm Laminate
Features
35dB Typical Gain Across
Frequency Band
POUT=27.5dBm<2.5% EVM
2.4GHz to 2.5GHz Frequency
Range
1x1 MIMO architecture
Integrated 3-stage PA,
filtering, and T/R switch.
Integrated power detector
Applications
WiFi IEEE802.11b/g/n
Applications
Customer Premises
Equipment (CPE)
WiFi Access Points and
Gateways
Spread-Spectrum and MMDS
Systems
Vbias
GND
GND
TXIN
GND
Input
Match
Pdown
Inter
Stage
Match
Inter
Stage
Match
Bias
Vtx
GND
GND
ANT
GND
Vrx
Functional Block Diagram
Product Description
RF5605 is a 1x1 MIMO module that is intently specified to address IEEE
802.11b/g/n WiFi 2.4GHz to 2.5GHz customer premises equipment (CPE) applica-
tions. The module has an integrated three-stage linear power amplifier, Tx harmonic
filtering and SPDT switch. The RF5605 has fully matched input and output for a
50system and incorporates matching networks optimized for linear output power
and efficiency. The RF5605 is housed in a 6mm x 6mm laminate.
Ordering Information
RF5605PCK-410
RF5605SB
RF5605SR
RF5605TR7
RF5605SQ
RF5605 Eval Board with 5 piece Bag
5 Piece Bag
100 piece Reel
2500 piece reel
25 piece Bag
DS120213
Optimum Technology Matching® Applied
GaAs HBT
SiGe BiCMOS
GaAs pHEMT
GaN HEMT
GaAs MESFET
InGaP HBT
Si BiCMOS
SiGe HBT
Si CMOS
Si BJT
BiFET HBT
LDMOS
RF MICRO DEVICES®, RFMD®, Optimum Technology Matching®, Enabling Wireless Connectivity™, PowerStar®, POLARIS™ TOTAL RADIO™ and UltimateBlue™ are trademarks of RFMD, LLC. BLUETOOTH is a trade-
mark owned by Bluetooth SIG, Inc., U.S.A. and licensed for use by RFMD. All other trade names, trademarks and registered trademarks are the property of their respective owners. ©2006, RF Micro Devices, Inc.
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at (+1) 336-678-5570 or [email protected].
1 of 17
Free Datasheet http://www.Datasheet4U.com

line_dark_gray
RF5605 equivalent
RF5605
Theory of Operation and Applications
Overview
The RF5605 is a single-chip integrated front end module (FEM) for high performance WiFi applications in the 2.4GHz to
2.5GHz ISM band. The FEM greatly reduces the number of external components minimizing footprint and assembly cost of the
overall 802.11b/g/n solution. The RF5605 has an integrated b/g/n power amplifier, a power Detector, and Tx filtering and a
Switch, which is capable of switching between WiFi Rx and WiFi Tx operations. The device is manufactured using InGaP HBT
and pHEMT processes on a 6mmx6mmx0.95mm Laminate package. The module meets or exceeds the RF front end needs of
the 802.11b/g/n WiFi RF systems. As the RF5605 is fully RF matched to 50internally and requires minimal external compo-
nents, it is very easy to implement on to PCB designs. To reduce the design and optimization process on the customer applica-
tion, the evaluation board layout should be copied as close as possible, in particular the ground and via configurations. Gerber
files of RFMD PCBA designs can be provided upon request. The supply voltage lines should present an RF short to the FEM by
using bypass capacitors on the VCC traces. To simplify bias conditions, the RF5605 requires a single positive supply voltage
(VCC), a positive current control bias (VREG) supply or high impedance enable, and a positive supply for switch control. The built-
in Power Detector of the RF5605 can be used as power monitor in the system. All inputs and outputs are internally matched to
50 .
Transmit Path
The RF5605 has a typical gain of 35dB from 2.4GHz to 2.5GHz, and delivers>27dBm typical output power in 11n HT20 MCS7
and>27.5dBm typical in 11g 54Mbps with an EVM<3%. The RF5605 requires a single positive of 5.0V to operate at full spec-
ifications. The VREG pin requires a regulated supply at 2.85V to maintain nominal bias current.
Out of Band Rejection
The RF5605 contains a low pass filter (LPF) to attenuate the 2nd Harmonics to -40dBm/MHz (typical). Depending upon the
end-user's application, additional filters may be needed to meet the out of band rejection requirements of the system. For the
system to meet FCC' s spec, a simple LC can be used between FEM and Antenna, for impedance matching and extra Harmon-
ics attenuation to meet spec.
Receive Path
The Rx path has a 50single-ended port. The Receive port return loss is 9.6dB minimum. In this mode, the FEM has an Inser-
tion loss of 0.8dB and 30dB (typical) isolation to Tx port.
RF5605 Biasing Instructions to the Eval board:
• 802.11b/g/n Transmit:
• Connect the FEM to a signal generator at the input and a spectrum analyzer at the output. Set the Pin at signal generator is
at -20dBm.
• Bias VCC to 5.0V first with VREG=0.0V. If available, enable the current limiting function of the power supply to 1100mA.
• Refer to switch operational truth table to set the control lines at the proper levels for WiFi Tx. It is recommended to maintain
at least 2.85V on VTx during Tx mode. A lower VTx voltage will enable the switch in Tx mode, but 2.85V is needed to ensure
that the switch stays in Tx mode during high power peaks. Using a VTx voltage less than 2.85V in Tx mode could result in
abnormal operation or device damage.
• Turn on VREG to 2.85V (typ.).
• On VREG (of Eval board), regulated supply is recommended. Be extremely careful not to exceed 3.0V on the VREG pin or the
part may exceed device current limits.
• Turn on PDOWN to 2.85V (typ.). PDOWN Pin can be tied to VREG supply.
NOTE: It is important to adjust the VCC voltage source so that +5V is measured at the board; and the +2.85V of VREG is
measured at the board. The high collector currents will drop the collector voltage significantly if long leads are used.
Adjust the bias voltage to compensate.
• Turn on RF of signal generator and gradually increase power level to the rated power.
CAUTION: If the input signal exceeds the maximum rated power, the RF5605 Evaluation Board can be permanently dam-
aged.
• To turn off FEM, turn off RF power of signal generator; then PDOWN, VREG and VCC.
DS120213
7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical
support, contact RFMD at (+1) 336-678-5570 or [email protected].
5 of 17
Free Datasheet http://www.Datasheet4U.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for RF5605 electronic component.


Information Total 17 Pages
Link URL [ Copy URL to Clipboard ]
Download [ RF5605.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
RF5601The function is Low Noise Amplifier. RF Micro DevicesRF Micro Devices
RF5602The function is 3GHz To 2.7GHz Linear Power Amplifier. RF Micro DevicesRF Micro Devices
RF5603The function is LINEAR POWER AMPLIFIER. RF Micro DevicesRF Micro Devices

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

RF56     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search