DataSheet39.com

What is UB10803?

This electronic component, produced by the manufacturer "Unisonic Technologies", performs the same function as "ONE-CELL STANDALONE LINEAR LITHIUM BATTERY CHARGER".


UB10803 Datasheet PDF - Unisonic Technologies

Part Number UB10803
Description ONE-CELL STANDALONE LINEAR LITHIUM BATTERY CHARGER
Manufacturers Unisonic Technologies 
Logo Unisonic Technologies Logo 


There is a preview and UB10803 download ( pdf file ) link at the bottom of this page.





Total 10 Pages



Preview 1 page

No Preview Available ! UB10803 datasheet, circuit

UNISONIC TECHNOLOGIES CO., LTD
UB10803
Preliminary
ONE-CELL STANDALONE
LINEAR LITHIUM BATTERY
CHARGER
CMOS IC
DESCRIPTION
SOP-8
The UTC UB10803 is a fully-integrated single-cell Li-ion/Polymer
battery charger. The device operates without external FET and
blocking diode, and employs a constant-current constant-voltage
(CC/CV) charging profile.
The fast-charge and end-of-charge (EOC) currents are
programmable with independent external resistors. When the battery
is deeply discharged to lower than 2.75V, the charger firstly
pre-charges the battery with typically 20% of the programmable
fast-charge current. When the charge current is reduced to the
programmed EOC current level (almost works completely in a
constant-voltage (CV) mode), an EOC indication is displayed through
the CHG pins. The UTC UB10803 is protected by thermal regulation
technology to prevent the IC from over-heat during charging.
Two status indication pins (PPR and CHG), which are both
implemented as an open-drain outputs, can be used to drive LEDs or
work as logic interface to a microprocessor. When no adapter is
attached or when the charger is disabled, the leakage current from
battery cell is less than 1uA typically.
FEATURES
1
DFN-8(2x3)
* A Constant-Current/Constant-Voltage Linear Charger
for Single-Cell Li-ion/Polymer Batteries
* Integrated Pass Element and Current Sensor
* Highly-Integrated, Requiring No External FETs or
Blocking Diode
* 4.2V Voltage Accuracy: ±1.2% All Temperatures
(Available with 4.10V and 4.36V options upon request)
* Programmable Charge Current 50mA to 500mA
* Programmable End-Of-Charge Current by Current
Recharge Algorithm
* Pre-Charge for Fully Discharged Batteries
* 1μA (Typ.) Leakage Current of the Battery when No
Input Power is Attached or Charger is Disabled
* Power Present and Charge Status Indications
* Thermal Regulation on Charging Current to Prevent
Over-Heat
* Few Components, Cost-Effective Solutions
ORDERING INFORMATION
Ordering Number
Lead Free
Halogen Free
UB10803L-SH2-T
UB10803G-SH2-T
UB10803L-SH2-R
UB10803G-SH2-R
UB10803L- K08-2030-R
UB10803G- K08-2030-R
Package
HSOP-8
HSOP-8
DFN-8(2×3)
Packing
Tube
Tape Reel
Tape Reel
www.unisonic.com.tw
Copyright © 2013 Unisonic Technologies Co., Ltd
1 of 10
QW-R502-A26.a
Free Datasheet http://www.Datasheet4U.com

line_dark_gray
UB10803 equivalent
UB10803
Preliminary
CMOS IC
OPERATION
The UTC UB10803 charges a single-cell Li-ion/Polymer battery with a programmed constant current (CC) or a
constant voltage (CV) profile. The constant fast charge current ICHG is programmable by setting an external resistor
RIREF while the constant voltage is factory-trimmed at 4.2V (4.10V or 4.36V options are available upon request). If the
battery voltage is deeply discharged to lower than 2.75V, The UTC UB10803 pre-charges the battery with a 20%
programmable current until the battery voltage rises above the pre-charge threshold. After pre-charge finishes,
constant-current (CC) charging mode begins with the pre-set fast charge current. Normally, the battery voltage rises
gradually during CC charge phase. When the battery voltage reaches nearly 4.2V, the charger enters the
constant-voltage (CV) charging mode and begins to regulate the battery voltage at 4.2V while diminishing the
charging current gradually. When the charging current is reduced to an amount smaller than the programmed
End-Of-Charge (EOC) current level, the charger gives out a “full-charge” indication through the CHG pin, but the
charger still continues to regulate the battery voltage at 4.2V with safe & small current.
The end-of-charge (EOC) current level (IMIN) can be easily programmed with an external resistor RIMIN. The CHG
signal turns to LOW when pre-charge starts and rises to HIGH when EOC is reached. After reaching EOC, the
charge current has to rise again to typically 76% of ICHG before the CHG signal will turn on again. The current surge
after EOC can be caused by a load connected to the battery.
When the die temperature reaches 115°C (typically), a thermal regulation function is employed to reduce the
charge current accordingly to maintain the temperature from increasing furthermore. This is an important function to
achieve safe operation even when the printed circuit board (PCB) is not effective in leaking out the heat generated
by the linear charger.
1. PPR Indication
The PPR pin is implemented as an open-drain output to provide a power-good indication of the input power source
such as an AC adapter. When the input voltage is higher than the POR (Power-On Reset) threshold, the PPR pin
turns on the internal open-drain MOSFET to indicate logic LOW signal. The PPR indication is designed to be
independent on the chip enable (EN-pin) input. When the internal open-drain FET is turned off, the PPR pin should
leak less than 1μA current. When turned on, the PPR pin should be able to sink at least 5mA current under all
operating conditions. The PPR pin can be used to drive an LED or worked as logic interface to a microprocessor.
2. Power-Good Range
The input voltage is considered as power good when it meets the following three conditions:
(1). VIN > VPOR
(2). VIN - VBAT > VOS
Where the VOS is the offset voltage, it determines if the battery voltage is even higher than the input voltage. All
VPOR and VOS are realized with sufficient hysteresis, as given in the Electrical Specification table. All charging
activities are disabled when the input voltage falls out of the power-good range.
3. Input and Output Comparator
Obviously, when the input source voltage is lower than the battery voltage, no charging activity could be started
and the charger will disable the internal pass element to prevent battery leakage. Charge begins when the input
voltage is higher than the battery voltage by a defined offset voltage (VOS). This scheme also ensures that the
charger is completely turned off when the input power is removed from the charger.
4. CHG Indication
The CHG pin is implemented as an open-drain output to give a logic LOW when a charge cycle begins and turn
HIGH when an end-of-charge (EOC) condition is reached. This pin is designed with a sinking ability of more than
5mA so as to drive an LED. When the charger is disabled through EN-pin, the CHG output is high impedance. The
CHG pin can also be used to interface with a microprocessor.
5. EN Input
The chip is enabled by a logic LOW signal applied to the EN pin. This pin is realized with a 200kinternal
pull-down resistor such that even the EN pin is left floating, the input is equivalent to logic LOW and the chip is
enabled by default. Similarly, the chip is disabled when the EN pin receives a logic HIGH signal.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 10
QW-R502-A26.a
Free Datasheet http://www.Datasheet4U.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for UB10803 electronic component.


Information Total 10 Pages
Link URL [ Copy URL to Clipboard ]
Download [ UB10803.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
UB10803The function is ONE-CELL STANDALONE LINEAR LITHIUM BATTERY CHARGER. Unisonic TechnologiesUnisonic Technologies

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

UB10     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search