DKI03062 Datasheet PDF - SANKEN
Part Number | DKI03062 | |
Description | N Channel Trench Power MOSFET | |
Manufacturers | SANKEN | |
Logo | ||
There is a preview and DKI03062 download ( pdf file ) link at the bottom of this page. Total 6 Pages |
Preview 1 page No Preview Available ! 30 V, 48 A, 5.2 mΩ Low RDS(ON)
N ch Trench Power MOSFET
DKI03062
Features
V(BR)DSS --------------------------------- 30 V (ID = 100 µA)
ID ---------------------------------------------------------- 48 A
RDS(ON) ------------ 6.5 mΩ max. (VGS = 10 V, ID = 31 A)
Qg------- 9.3 nC (VGS = 4.5 V, VDS = 15 V, ID = 39.5 A)
Low Total Gate Charge
High Speed Switching
Low On-Resistance
Capable of 4.5 V Gate Drive
100 % UIL Tested
RoHS Compliant
Package
TO-252
(4)
D
(1) (2) (3)
GDS
(3) (2) (1)
SDG
Applications
DC-DC converters
Synchronous Rectification
Power Supplies
Equivalent circuit
D(2)(4)
G(1)
S(3)
Not to scale
Absolute Maximum Ratings
Unless otherwise specified, TA = 25 °C
Parameter
Symbol
Drain to Source Voltage
VDS
Gate to Source Voltage
VGS
Continuous Drain Current
ID
Pulsed Drain Current
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
IDM
IS
ISM
Single Pulse Avalanche Energy
EAS
Avalanche Current
Power Dissipation
Operating Junction Temperature
Storage Temperature Range
IAS
PD
TJ
TSTG
Test conditions
TC = 25 °C
PW ≤ 100µs
Duty cycle ≤ 1 %
PW ≤ 100µs
Duty cycle ≤ 1 %
VDD = 20 V, L = 1 mH,
IAS = 5.5 A, unclamped,
RG = 4.7 Ω
Refer to Figure 1
TC = 25 °C
Rating
30
± 20
48
96
48
96
47
13.3
37
150
− 55 to 150
Unit
V
V
A
A
A
A
mJ
A
W
°C
°C
DKI03062-DS Rev.1.2
Jan. 24, 2014
SANKEN ELECTRIC CO.,LTD.
http://www.sanken-ele.co.jp
1
http://www.Datasheet4U.com
|
|
DKI03062
OPERATING PRECAUTIONS
In the case that you use Sanken products or design your products by using Sanken products, the reliability largely
depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation
range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to
assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric
current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused
due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum
values must be taken into consideration. In addition, it should be noted that since power devices or IC’s including power
devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly.
Because reliability can be affected adversely by improper storage environments and handling methods, please
observe the following cautions.
Cautions for Storage
Ensure that storage conditions comply with the standard temperature (5 to 35°C) and the standard relative humidity
(around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity.
Avoid locations where dust or harmful gases are present and avoid direct sunlight.
Reinspect for rust on leads and solderability of the products that have been stored for a long time.
Remarks About Using Silicone Grease with a Heatsink
When silicone grease is used in mounting the products on a heatsink, it shall be applied evenly and thinly. If more
silicone grease than required is applied, it may produce excess stress.
Volatile-type silicone greases may crack after long periods of time, resulting in reduced heat radiation effect.
Silicone greases with low consistency (hard grease) may cause cracks in the mold resin when screwing the
products to a heatsink.
Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the
product life, are indicated below:
Type
Suppliers
G746 Shin-Etsu Chemical Co., Ltd.
YG6260 Momentive Performance Materials Inc.
SC102 Dow Corning Toray Co., Ltd.
Cautions for Testing and Handling
When tests are carried out during inspection testing and other standard test periods, protect the products from power
surges from the testing device, shorts between the product pins, and wrong connections. Ensure all test parameters are
within the ratings specified by Sanken for the products.
Soldering
When soldering the products, please be sure to minimize the working time, within the following limits:
・Reflow
Preheat ; 180 °C / 90 ± 30 s
Solder heating ; 250 °C / 10 ± 1s (260 °C peak, 2 times)
・Soldering iron ; 380 ± 10 °C / 3.5 ± 0.5s (1 time)
Electrostatic Discharge
When handling the products, the operator must be grounded. Grounded wrist straps worn should have at least 1MΩ
of resistance from the operator to ground to prevent shock hazard, and it should be placed near the operator.
Workbenches where the products are handled should be grounded and be provided with conductive table and floor
mats.
When using measuring equipment such as a curve tracer, the equipment should be grounded.
When soldering the products, the head of soldering irons or the solder bath must be grounded in order to prevent
leak voltages generated by them from being applied to the products.
The products should always be stored and transported in Sanken shipping containers or conductive containers, or
be wrapped in aluminum foil.
DKI03062-DS Rev.1.2
Jan. 24, 2014
SANKEN ELECTRIC CO.,LTD.
5
http://www.Datasheet4U.com
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DKI03062 electronic component. |
Information | Total 6 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ DKI03062.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
DKI03062 | The function is N Channel Trench Power MOSFET. SANKEN | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DKI0
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |