|
|
Número de pieza | HFA1150IH96 | |
Descripción | 700MHz/ SOT-23/ Low Distortion Current Feedback Operational Amplifier | |
Fabricantes | Intersil Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de HFA1150IH96 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
No Preview Available ! TM
Data Sheet
HFA1150
March 2000
File Number 4836
700MHz, SOT-23, Low Distortion Current
Feedback Operational Amplifier
The HFA1150 is a high-speed, wideband, fast settling op
amp built with Intersil's proprietary complementary bipolar
UHF-1 process. The current feedback architecture delivers
superb bandwidth even at very high gains (>300MHz at
AV = 10), and the low distortion and excellent video
parameters make this amplifier ideal for communication and
professional video applications.
Though specified for ±5V operation, the HFA1150 operates
with single supply voltages as low as 4.5V, and requires only
3.4mA of Icc in 5V applications (see Application Information
section, and Application Note AN9891).
For a lower power amplifier in a SOT-23 package, please
refer to the HFA1155 data sheet.
Ordering Information
PART NUMBER
(BRAND)
HFA1150IB
(H1150I)
HFA1150IB96
(H1150I)
TEMP.
RANGE
(oC)
PACKAGE
-40 to 85 8 Ld SOIC
-40 to 85 8 Ld SOIC
Tape and Reel
PKG. NO.
M8.15
M8.15
HFA1150IH96
(1150)
-40 to 85 5 Ld SOT-23 Tape P5.064
and Reel
HFA11XXEVAL
DIP Evaluation Board for High-Speed Op
Amps
OPAMPSOT23EVAL SOT-23 Evaluation Board for High-Speed Op
Amps
Pinouts
HFA1150
(SOIC)
TOP VIEW
NC 1
-IN 2
+IN 3
V- 4
-
+
8 NC
7 V+
6 OUT
5 NC
Features
• Low Distortion (5MHz, HD2). . . . . . . . . . . . . . . . . . -67dBc
• -3dB Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . 700MHz
• High Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . 2700V/µs
• Fast Settling Time (0.1%) . . . . . . . . . . . . . . . . . . . . . 20ns
• Excellent Gain Flatness . . . . . . . . . . ±0.05dB to 100MHz
• High Output Current . . . . . . . . . . . . . . . . . . . . . . . . . 60mA
• Fast Overdrive Recovery . . . . . . . . . . . . . . . . . . . . . <5ns
• Operates with 5V Single Supply (See AN9891)
Applications
• Video Switching and Routing
• Pulse and Video Amplifiers
• RF/IF Signal Processing
• Flash A/D Driver
• Medical Imaging Systems
• Related Literature
- AN9420, Current Feedback Theory
- AN9891, Single 5V Supply Operation
HFA1150
(SOT23)
TOP VIEW
OUT 1
V- 2
+IN 3
5 V+
4 -IN
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000
1 page HFA1150
50
AV = +2
40
30
20
SOIC
10
SOT-23
0
0 50 100 150 200 250 300 350 400
LOAD CAPACITANCE (pF)
FIGURE 1. RECOMMENDED SERIES OUTPUT RESISTOR vs
LOAD CAPACITANCE
PC Board Layout
The frequency response of this amplifier depends greatly on
the amount of care taken in designing the PC board. The
use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
chip (0.1µF) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Output capacitance, such as
that resulting from an improperly terminated transmission
line, will degrade the frequency response of the amplifier
and may cause oscillations. In most cases, the oscillation
can be avoided by placing a resistor in series with the output.
Care must also be taken to minimize the capacitance to ground
seen by the amplifier’s inverting input. The larger this
capacitance, the worse the gain peaking, resulting in pulse
overshoot and eventual instability. To reduce this capacitance,
remove the ground plane under traces connected to -IN and
keep these traces as short as possible.
Examples of good high frequency layouts are the evaluation
boards shown below.
Evaluation Boards
The performance of the HFA1150IB (SOIC) may be
evaluated using the HFA11XX Evaluation Board and a SOIC
to DIP adaptor like the Aries Electronics Part Number
08-350000-10. The SOT-23 version can be evaluated using
the OPAMPSOT23EVAL board.
To order evaluation boards (part number HFA11XXEVAL or
OPAMPSOT23EVAL), please contact your local sales office.
The schematic and layout of the HFA11XXEVAL and
OPAMPSOT23EVAL boards are shown below.
511Ω
511Ω
NC
1
50Ω 2
IN 3
4
-5V
8
7
6
5
GND
0.1µF
10µF
50Ω +5V
OUT
NC
GND
FIGURE 2. HFA11XXEVAL SCHEMATIC
HFA11XXEVAL TOP LAYOUT
VH
1
+IN
VL V-
V+
GND
HFA11XXEVAL BOTTOM LAYOUT
5
5 Page Die Characteristics
DIE DIMENSIONS:
53 mils x 25mils
1350µm x 630µm
METALLIZATION:
Type: Metal 1: AlCu (2%)/TiW
Thickness: Metal 1: 8kÅ ±0.4kÅ
Type: Metal 2: AlCu (2%)
Thickness: Metal 2: 16kÅ ±0.8kÅ
Metallization Mask Layout
HFA1150
PASSIVATION:
Type: Nitride
Thickness: 4kÅ ±0.5kÅ
TRANSISTOR COUNT:
40
SUBSTRATE POTENTIAL (POWERED UP):
Floating (Recommend Connection to V-)
HFA1150
V+ OUT
V-
-IN +IN
11
11 Page |
Páginas | Total 13 Páginas | |
PDF Descargar | [ Datasheet HFA1150IH96.PDF ] |
Número de pieza | Descripción | Fabricantes |
HFA1150IH96 | 700MHz/ SOT-23/ Low Distortion Current Feedback Operational Amplifier | Intersil Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |