G156XW01_V0 Datasheet PDF - AUO
Part Number | G156XW01_V0 | |
Description | LCD Module | |
Manufacturers | AUO | |
Logo | ||
There is a preview and G156XW01_V0 download ( pdf file ) link at the bottom of this page. Total 28 Pages |
Preview 1 page No Preview Available ! www.DataSheet4U.net
Avnet Embedded.
Support Around The Board™
Avnet Embedded
Specification.
Datasheet
AUO G156XW01-V0
www.avnet-embedded.eu
|
|
www.DataSheet4U.net
Product Specification
AU OPTRONICS CORPORATION
G156XW01 V0
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the CCFL reflector edge. Instead, press at
the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version 1.0
4
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for G156XW01_V0 electronic component. |
Information | Total 28 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ G156XW01_V0.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
G156XW01-V0 | The function is LCD Module. AUO | |
G156XW01-V1 | The function is LCD Module. AUO | |
G156XW01_V0 | The function is LCD Module. AUO | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
G156
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |