|
|
Número de pieza | 78Q2120C | |
Descripción | 10/100BASE-TX Transceiver | |
Fabricantes | TDK Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de 78Q2120C (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! www.DataSheet4U.com
78Q2120C
10/100BASE-TX Transceiver
DESCRIPTION
The 78Q2120C is a 10BASE-T/100BASE-TX Fast
Ethernet transceiver. It includes integrated MII,
ENDECs, scrambler/descrambler, dual-speed clock
recovery, and full-featured auto-negotiation function.
The transmitter includes an on-chip pulse-shaper and
a low-power line driver. The receiver has an adaptive
equalizer and a baseline restoration circuit required
for accurate clock and data recovery. The transceiver
interfaces to Category-5 unshielded twisted pair (Cat-
5 UTP) cabling for 100BASE-TX/10BASE-T and
Category-3 unshielded twisted pair for 10BASE-T,
and is connected to the line media via 1:1 isolation
transformers. No external filter is required. Interface
to the MAC is accomplished through an IEEE-802.3
compliant Media Independent Interface (MII). The
product is fabricated in an advanced CMOS process
for high performance and low power operation.
FEATURES
August 2003
• 10BASE-T/100BASE-TX IEEE-802.3 compliant
TX and RX functions requiring a dual 1:1
isolation transformer interface to the line
• Integrated MII, 10BASE-T/100BASE-TX ENDEC,
100BASE-TX scrambler/descrambler, and full-
featured auto-negotiation function
• Full duplex operation capable
• PCS Bypass supports 5-bit symbol interface
• Register-programmable transmit amplitude
• Dual speed digital clock recovery
• Automatic polarity correction during auto-
negotiation and 10BASE-T signal reception
• Power-saving and power-down modes
including transmitter disable
• LED indicators: LINK, TX, RX, COL, 100, 10,
FDX
• User programmable Interrupt pin
• 64-Pin TQFP (JEDEC LQFP) package
• Single 3.3 V ± 0.3V Supply
BLOCK DIAGRAM
RX_CLK
TX_CLK
RXD[3:0]
TXD[3:0]
4B/5B Encoder,
100M
Scrambler,
Parallel/Serial
NRZ/NRZI
MLT3 Encoder
MII
Registers
&
Interface
Logic
10M Parallel/Serial,
MMaanncchheesstteerr EEnnccooddeerr
TX CLK GEN
Manchester Decoder,
Parallel/Serial
Carrier Sense,
CCoollliissiioonn DDeetteecctt
CLK
Recovery
Serial/Parallel
Descrambler,
5B/4B Decoder
CClloocckk RReeffeerreennccee
PS
PPuullssee SShhaappeerr
and Filter
TXOP/N
Auto
Negotiation
MDI
RXIP/N
10M 100M
Adaptive EQ,
Baseline Wander Correct,
MMLLTT33 DDeeccooddee,, NNRRZZII//NNRRZZ
LEDs
VCC GND
LEDL LEDBTX LEDTX LEDCOL
CKIN 25MHz
LEDBT LEDFX
LEDRX
© 2003 TDK Semiconductor Corporation, Proprietary and Confidential
Rev_1.1
1 page 78Q2120C
10/100BASE-TX Transceiver
transitions synchronously with respect to RX_CLK
and is asserted when the 78Q2120C is presenting
valid data on RXD[3:0]. RX_ER is asserted when a
code group violation has been detected in the
current receive packet and is also synchronous to
RX_CLK.
Station Management Interface
The station management interface consists of
circuitry which implements the serial protocol as
described in Clause 22.2.4.5 of IEEE-802.3. A 16-
bit shift register receives serial data applied to the
MDIO pin at the rising-edge of the MDC clock signal.
Once the preamble is received, the station
management control logic looks for the start-of-
frame sequence and a read or write op-code,
followed by the PHYAD and REGAD fields. For a
read operation, the MDIO port becomes enabled as
an output and the register data is loaded into a shift
register for transmission. The 78Q2120C can work
with a one bit preamble rather than the 32 bits
proscribed by IEEE-802.3. This allows for faster
programming of the registers. If a register does not
exist at an address indicated by the REGAD field or
if the PHYAD field does not match the 78Q2120C
PHYAD indicated by the PHYAD pins, a read of the
MDIO port will return all ones. For a write operation,
the data is shifted in and loaded into the appropriate
register after the sixteenth data bit has been
received.
www.DataSheet4U.com
When the PHYAD field is all zeros, the Station
Management Entity (STA) is requesting a broadcast
data transaction. All PHYs sharing the same
Management Interface must respond to this
broadcast request. The 78Q2120C will respond to
the broadcast data transaction.
ADDITIONAL FEATURES
LED Indicators
There are seven LED pins that can be used to
indicate various states of operation of the
78Q2120C. There is an LED pin that indicates the
link is up (LEDL), others that indicates the
78Q2120C is either transmitting (LEDTX) or
receiving (LEDRX), one that signals a collision event
(LEDCOL), two more that reflect the data rate
(LEDBTX and LEDBT), and one that reflects full
duplex mode of operation (LEDFDX).
Interrupt Pin
The 78Q2120C has an Interrupt pin (INTR) that is
asserted whenever any of the eight interrupt bits of
MR17.7:0 are set. These interrupt bits can be
disabled via MR17.15:8 Interrupt Enable bits. The
Interrupt Level bit, MR16.14, controls the active level
of the INTR pin. When the INTR pin is not asserted,
the pin is held in a high impedance state.
© 2003 TDK Semiconductor Corporation, Proprietary and Confidential
-5-
Rev_1.1
5 Page 78Q2120C
10/100BASE-TX Transceiver
www.DataSheet4U.com
MR0: Control Register
Bit Symbol Type
0.15 RESET R/SC
0.14 LOOPBK R/W
0.13 SPEEDSL R/W
0.12 ANEGEN R/W
0.11 PWRDN R/W
0.10 ISO R/W
0.9 RANEG R/SC
Default
0
0
(1)
(1)
0
(0)
0
Description
Reset: Setting this bit to ‘1’ resets the device and sets all registers to
their default states. This bit is self-clearing.
Loopback: When this bit is set to ‘1’, no transmission of data on the
network medium occurs and any receive data on the network medium
is ignored. By default, the loopback signal path will encompass as
much of the 78Q2120C circuitry as possible.
Speed Selection: This bit determines the speed of operation of the
78Q2120C. Setting this bit to ‘1’ indicates 100Base-TX operation and
a ‘0’ indicates 10Base-T mode. This bit will default to a ‘1’ upon reset.
If the TECH[2:0] pins are all logic zero and auto-negotiation is not
enabled, this bit will be writeable. If auto-negotiation is not enabled
and the TECH[2:0] pins are set to indicate that only 10Base-T is
supported, this bit will be forced to logic zero and will not be writeable.
If auto-negotiation is not enabled and the TECH[2:0] pins are set to
indicate that only 100Base-TX is supported, this bit will be forced to
logic one and will not be writeable. When auto-negotiation is enabled,
this bit will not be writeable and will have no effect on the 78Q2120C.
If the TECH[2:0] pins are brought to zero from another value, this bit
will retain its original value until it is overwritten.
Auto-Negotiation Enable: Setting this bit to ‘1’ shall enable The auto-
negotiation process. This bit can only be set if the ANEGA pin is a
logic one and will default to ‘1’ upon reset in this case. If this bit is
cleared to ‘0’, manual speed and duplex mode selection is
accomplished through bits 0.13 (SPEEDSL) and 0.8 (DUPLEX) of the
Control Register or the TECH[2:0] pins according to the table shown in
the section describing the TECH[2:0] pins. If the ANEGA pin is
brought from ‘0’ to ‘1’ and reset is not asserted, this bit will remain at
‘0’ until a ‘1’ is written.
Power-Down: The device may be placed in a low power consumption
state by setting this bit to ‘1’. While in power-down state, the device
will still respond to management transactions. Setting the PWRDN pin
high can also activate the power-down state.
Isolate: When set to ‘1’, the device will present a high-impedance on
its MII output pins. This allows for multiple PHY’s to be attached to
the same MII interface. When the device is isolated, it still responds to
management transactions. The default value of this bit depends on
the ISODEF pin. When ISODEF pin is tied high, the ISO bit defaults
to high. Otherwise, it defaults to low. The Isolate mode can also be
activated through the ISO pin.
Restart Auto-Negotiation: Normally, the Auto-Negotiation process is
started at power up. The process can be restarted by setting this bit
to ‘1’. This bit is self-clearing.
© 2003 TDK Semiconductor Corporation, Proprietary and Confidential
- 11 -
Rev_1.1
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet 78Q2120C.PDF ] |
Número de pieza | Descripción | Fabricantes |
78Q2120C | 10/100BASE-TX Transceiver | TDK Semiconductor |
78Q2120C | 10/100BASE-TX Transceiver | Teridian |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |