|
|
Número de pieza | MC74HC366 | |
Descripción | Hex 3-State Inverting Buffer | |
Fabricantes | Motorola Semiconductors | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de MC74HC366 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Hex 3-State Inverting Buffer
with Common Enables
High–Performance Silicon–Gate CMOS
The MC54/74HC366 is identical in pinout to the LS366. The device inputs
are compatible with standard CMOS outputs; with pullup resistors, they are
compatible with LSTTL outputs.
This device is a high–speed hex buffer with 3–state outputs and two
common active–low Output Enables. When either of the enables is high, the
buffer outputs are placed into high–impedance states. The HC366 has
inverting outputs.
• Output Drive Capability: 15 LSTTL Loads
• Outputs Directly Interface to CMOS, NMOS, and TTL
• Operating Voltage Range: 2 to 6 V
• Low Input Current: 1 µA
• High Noise Immunity Characteristic of CMOS Devices
• In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
• Chip Complexity: 78 FETs or 19.5 Equivalent Gates
LOGIC DIAGRAM
A0 2
A1 4
A2 6
A3 10
A4 12
OUTPUT ENABLE 1 1
OUTPUT ENABLE 2 15
A5 14
3 Y0
5 Y1
7 Y2
9 Y3
11 Y4
13 Y5
PIN 16 = VCC
PIN 8 = GND
www.DataSheet4U.com
MC54/74HC366
16
1
J SUFFIX
CERAMIC PACKAGE
CASE 620–10
16
1
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ORDERING INFORMATION
MC54HCXXXJ
MC74HCXXXN
Ceramic
Plastic
PIN ASSIGNMENT
OUTPUT
ENABLE 1
A0
Y0
1
2
3
16 VCC
15
OUTPUT
ENABLE 2
14 A5
A1 4
13 Y5
Y1 5
12 A4
A2 6
11 Y4
Y2 7
10 A3
GND 8
9 Y3
FUNCTION TABLE
Enable
1
Inputs
Enable
2
A
Output
Y
L
LL
H
L
LH
L
H
XX
Z
X
HX
Z
X = don’t care
Z = high impedance
10/95
© Motorola, Inc. 1995
1 REV 6
1 page –A
–
16
1
OUTLINE DIMENSIONS
J SUFFIX
CERAMIC PACKAGE
CASE 620–10
ISSUE V
9
–B
–
8
C
L
–T
SEAT–ING
PLANE
F
NK
E
G
D 16 PL
0.25 (0.010) M T A S
M
J 16 PL
0.25 (0.010) M T B S
MC54/74HC366
www.DataSheet4U.com
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIM F MAY NARROW TO 0.76 (0.030) WHERE
THE LEAD ENTERS THE CERAMIC BODY.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.750 0.785 19.05 19.93
B 0.240 0.295 6.10 7.49
C — 0.200 — 5.08
D 0.015 0.020 0.39 0.50
E 0.050 BSC 1.27 BSC
F 0.055 0.065 1.40 1.65
G 0.100 BSC
2.54 BSC
J 0.008 0.015 0.21 0.38
K 0.125 0.170 3.18 4.31
L 0.300 BSC 7.62 BSC
M 0° 15° 0° 15°
N 0.020 0.040 0.51 1.01
–A
–
16
1
H
G
9
B
8
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
FC
S
–T
–
SEATING
PLANE
K
J
D 16 PL
0.25 (0.010) M T A M
L
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.070 1.02 1.77
G
0.100 BSC
2.54 BSC
H
0.050 BSC
1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M
0° 10°
0° 10°
S 0.020 0.040 0.51 1.01
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] –TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
High–Speed CMOS Logic Data
DL129 — Rev 6
◊ CODELINE
MC54/74HC366/D
5 *MC54/74HC366/D* MOTOROLA
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet MC74HC366.PDF ] |
Número de pieza | Descripción | Fabricantes |
MC74HC365 | Hex 3-State Noninverting Buffer | Motorola Semiconductors |
MC74HC365A | Hex 3-State Noninverting Buffer | ON Semiconductor |
MC74HC366 | Hex 3-State Inverting Buffer | Motorola Semiconductors |
MC74HC367A | Hex 3-State Noninverting Buffer with Separate 2-Bit and 4-Bit Sections | Motorola Semiconductors |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |