DataSheet39.com

What is ADM1027?

This electronic component, produced by the manufacturer "Analog Devices", performs the same function as "dBCOOL Remote Thermal Controller and Voltage Monitor".


ADM1027 Datasheet PDF - Analog Devices

Part Number ADM1027
Description dBCOOL Remote Thermal Controller and Voltage Monitor
Manufacturers Analog Devices 
Logo Analog Devices Logo 


There is a preview and ADM1027 download ( pdf file ) link at the bottom of this page.





Total 30 Pages



Preview 1 page

No Preview Available ! ADM1027 datasheet, circuit

dBCOOL Remote Thermalwww.DataSheet4U.com
Controller and Voltage Monitor
ADM1027*
FEATURES
Monitors up to 5 Supply Voltages
Controls and Monitors up to 4 Fan Speeds
1 On-Chip and 2 Remote Temperature Sensors
Monitors up to 5 Processor VID Bits
Automatic Fan Speed Control Mode Controls System
Cooling Based on Measured Temperature
Enhanced Acoustic Mode Dramatically Reduces User
Perception of Changing Fan Speeds
2-Wire and 3-Wire Fan Speed Measurement
Limit Comparison of All Monitored Values
Meets SMBus 2.0 Electrical Specifications
(Fully SMBus 1.1 Compliant)
APPLICATIONS
Low Acoustic Noise PCs
Networking and Telecommunications Equipment
GENERAL DESCRIPTION
The ADM1027 dBCOOL controller is a complete systems
monitor and multiple PWM fan controller for noise sensitive
applications requiring active system cooling. It can monitor
12 V, 5 V, 2.5 V CPU supply voltage, plus its own supply volt-
age. It can monitor the temperature of up to two remote sensor
diodes, plus its own internal temperature. It can measure and
control the speed of up to four fans so that they operate at the
lowest possible speed for minimum acoustic noise. The auto-
matic fan speed control loop optimizes fan speed for a given
temperature. Once the control loop parameters are programmed,
the ADM1027 can vary fan speed without CPU intervention.
FUNCTIONAL BLOCK DIAGRAM
ADDR
SELECT ADDR EN SCL SDA SMBALERT
VID4
VID3
VID2
VID1
VID0
PWM1
PWM2
PWM3
TACH1
TACH2
TACH3
TACH4
VCC
D1+
D1–
D2+
D2–
+5VIN
+12VIN
+2.5VIN
VCCP
PWM
REGISTERS
AND
CONTROLLERS
VID
REGISTER
ACOUSTIC
ENHANCEMENT
CONTROL
SMBUS
ADDRESS
SELECTION
SERIAL BUS
INTERFACE
ADDRESS
POINTER
REGISTER
AUTOMATIC
FAN SPEED
CONTROL
PWM
CONFIGURATION
REGISTERS
VCC TO ADM1027
FAN SPEED
COUNTER
BAND GAP
TEMP. SENSOR
INPUT
SIGNAL
CONDITIONING
AND
ANALOG
MULTIPLEXER
ADM1027
10-BIT
ADC
BAND GAP
REFERENCE
INTERRUPT
MASKING
INTERRUPT
STATUS
REGISTERS
LIMIT
COMPARATORS
VALUE AND
LIMIT
REGISTERS
GND
*Protected by U.S. Patent Nos. 6,188,189; 6,169,442; 6,097,239; 5,982,221;
and 5,867,012. Other patents pending.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703 © 2003 Analog Devices, Inc. All rights reserved.

line_dark_gray
ADM1027 equivalent
ADM1027www.DataSheet4U.com
PIN FUNCTION DESCRIPTIONS
Pin Mnemonic
Description
1 SDA
Digital I/O (Open-Drain). SMBus bidirectional serial data. Requires SMBus pull-up.
2 SCL
Digital Input (Open-Drain). SMBus serial clock input. Requires SMBus pull-up.
3 GND
Ground Pin for the ADM1027.
4 VCC
Power Supply. Can be powered by 3.3 V standby if monitoring in low power states is required.
VCC is also monitored through this pin. The ADM1027 can also be powered from a 5 V supply.
Setting Bit 7 of Configuration Register 1 (Reg. 0x40) rescales the VCC input attenuators to
correctly measure a 5 V supply.
5 VID0
Digital Input (Open-Drain). Voltage supply readouts from CPU. This value is read into the
VID register (Reg. 0x43).
6 VID1
Digital Input (Open-Drain). Voltage supply readouts from CPU. This value is read into the
VID register (Reg. 0x43).
7 VID2
Digital Input (Open-Drain). Voltage supply readouts from CPU. This value is read into the
VID register (Reg. 0x43).
8 VID3
Digital Input (Open-Drain). Voltage supply readouts from CPU. This value is read into the
VID register (Reg. 0x43).
9 TACH3
10 PWM2/SMBALERT
Digital Input (Open-Drain). Fan tachometer input to measure speed of Fan 3. Can be
reconfigured as an analog input (AIN3) to measure the speed of 2-wire fans.
Digital Output (Open-Drain). Requires 10 kW typical pull-up. Pulsewidth modulated output
to control Fan 2 speed. This pin may be reconfigured as an SMBALERT interrupt output to
signal out-of-limit conditions.
11 TACH1
Digital Input (Open-Drain). Fan tachometer input to measure speed of Fan 1. Can be
reconfigured as an analog input (AIN1) to measure the speed of 2-wire fans.
12 TACH2
Digital Input (Open-Drain). Fan tachometer input to measure speed of Fan 2. Can be
reconfigured as an analog input (AIN2) to measure the speed of 2-wire fans.
13 PWM3/ADDRESS ENABLE Digital I/O (Open-Drain). Pulsewidth modulated output to control Fan 3 speed. Requires
10 kW typical pull-up. If pulled low on power-up, this places the ADM1027 into address
select mode, and the state of Pin 14 will determine the ADM1027’s slave address.
14 TACH4/ADDRESS SELECT Digital Input (Open-Drain). Fan tachometer input to measure speed of Fan 4. Can be reconfigured
as an analog input (AIN4) to measure the speed of 2-wire fans. If in address select mode,
this pin determines the SMBus device address.
15 D2–
Cathode Connection to Second Thermal Diode.
16 D2+
Anode Connection to Second Thermal Diode.
17 D1–
Cathode Connection to First Thermal Diode.
18 D1+
Anode Connection to First Thermal Diode.
19 VID4
Digital Input (Open-Drain). Voltage supply readouts from CPU. This value is read into the
VID register (Reg. 0x43).
20 5VIN
21 12VIN
22 2.5VIN
23 VCCP
24 PWM1/XTO
Analog Input. Monitors 5 V power supply.
Analog Input. Monitors 12 V power supply.
Analog Input. Monitors 2.5 V supply, typically a chipset voltage.
Analog Input. Monitors processor core voltage (0 V to 3 V).
Digital Output (Open-Drain). Pulsewidth modulated output to control Fan 1 speed. Requires
10 kW typical pull-up. Also functions as the output from the XOR tree in XOR test mode.
REV. A
–5–


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ADM1027 electronic component.


Information Total 30 Pages
Link URL [ Copy URL to Clipboard ]
Download [ ADM1027.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
ADM1020The function is 8-Lead/ Low-Cost/ System Temperature Monitor. Analog DevicesAnalog Devices
ADM1021The function is Low Cost Microprocessor System Temperature Monitor. Analog DevicesAnalog Devices
ADM1021AThe function is Low Cost Microprocessor System Temperature Monitor Microcomputer. ON SemiconductorON Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

ADM1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search