No Preview Available !
Resistors
Thick film rectangular
MCR006 (0201 size : 1 / 20W)
MCR006
zFeatures
1) Extremely small light
Area ratio is 60% smaller than that of chip 1005, while weight ratio has been cut 80%.
2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Flat surface further facilitates mounting
5) ROHM resistors have approved ISO–9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
zRatings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
Specifications
0.05W (1 / 20W)
at 70°C
80
60
40
20
0 −55
0 70 100 125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E= P×R
E: Rated voltage (V)
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
See Table 1.
Operating temperature
Limiting element voltage 25V
−55°C to +125°C
1/5
Resistors
2.0
JIS C 5201-1 4.18
1.5 SAMPLE SIZE : n=10pcs
SOLDERING CONDITION
1.0 : 260°C 10s
0.5
0.0
−0.5
−1.0
−1.5
−2.0
10
100 1k 10k 100k
RESISTANCE (Ω)
1M
Fig.8 Resistance to soldering heat
MCR006
2.0
JIS C 5201-1 4.19
1.5 SAMPLE SIZE : n=10pcs
−55°C / 125°C 100cyc
1.0
0.5
0
−0.5
−1.0
−1.5
−2.0
10
100 1k 10k 100k
RESISTANCE (Ω)
1M
Fig.9 Rapid change of
temperature
4.0
JIS C 5201-1 4.24
3.0 SAMPLE SIZE : n=10pcs
40°C 93%RH WITH NO LOAD
2.0 1000h
1.0
0
−1.0
−2.0
−3.0
−4.0
10
100 1k 10k 100k
RESISTANCE (Ω)
1M
Fig.10 Damp heat, steady state
4.0
JIS C 5201-1 4.24
3.0 SAMPLE SIZE : n=10pcs
40°C 93%RH WITH NO LOAD
2.0 1000h
1.0
0
−1.0
−2.0
−3.0
−4.0
10
100 1k 10k 100k
RESISTANCE (Ω)
1M
Fig.11 Endurance at 70°C
2.0
1.5
1.0
0.5
0
−0.5
−1.0
−1.5
−2.0
10
JIS C 5201-1 4.19
SAMPLE SIZE : n=10pcs
−55°C / 125°C 100cyc
100 1k 10k 100k
RESISTANCE (Ω)
Fig.12 Endurance
1M
2.0
JIS C 5201-1 4.29
1.5 SAMPLE SIZE : n=10pcs
IPA, 5min.
1.0
0.5
0
−0.5
−1.0
−1.5
−2.0
10
100 1k 10k 100k
RESISTANCE (Ω)
1M
Fig.13 Resistance to solvents
2.0
JIS C 5201-1 4.33
1.5 SAMPLE SIZE : n=10pcs
ENDURANCE WITH 90mm WIDTH
1.0
0.5
0.0
−0.5
−1.0
−1.5
−2.0
10 100 1k 10k 100k 1M
RESISTANCE (Ω)
Fig.14 Bend strength of
the end face plating
5/5