GS-R24P Datasheet PDF - ST Microelectronics
Part Number | GS-R24P | |
Description | STEP-DOWN SWITCHING REGULATOR FAMILY | |
Manufacturers | ST Microelectronics | |
Logo | ||
There is a preview and GS-R24P download ( pdf file ) link at the bottom of this page. Total 7 Pages |
Preview 1 page No Preview Available ! www.DataSheet4U.com
GS-R24P
1.8W TO 8W STEP-DOWN SWITCHING REGULATOR FAMILY
FEATURE
■ MTBF 1 000 000 hours (Tamb=25)C)
■ 1.5A max output current
■ 35V max input voltage
■ 1.5V max drop-out voltage
■ Remote logic inhibit/enable
■ Not-latching overload and short circuit
protection
■ Thermal shutdown
■ Fixed or adjustable output
■ No heatsink required
PRELIMINARY
DESCRIPTION
The GS-R24P series is a family of high efficiency
step down switching voltage regulator, designed to
replace linear regulators.
Based on STM L5973 device, this non isolated family
of regulators are suitable for the full spectrum of ap-
plications including telecom, industry, computer and
distributed power system applications having a wide-
ly ranging input voltage.
Packing type: V = vertical PTH
Packing type: H = horizontal PTH
-------------------S = horizontal SMD
June 2004
This is preliminary information on a new product now in development. Details are subject to change without notice.
1/7
|
|
USER NOTES
Input Voltage
The recommended operating maximum DC Input Voltage is 35V inclusive of ripple voltage.
GS-R24P
Inhibit function
The inhibit feature allows to put in stand-by mode the device.
With INH pin 4 higher than 2.2V the device is disabled and the power consumption is reduced to less than
150µA for Vi = 35V.
With INH pin lower than 0.8V, the device is enabled.
If the INH pin is left floating, an internal pull up ensures that the voltage at the pin reaches the inhibit threshold
and the device is disabled.
The pin is also Vi compatible.
Current protection
The device has two current limit protections, pulse by pulse and frequency fold back.
The current is sensed through a resistor and if reaches the threshold, the on time is reduced and consequently
the output voltage too.
Since the minimum switch ON time (necessary to avoid false overcurrent signal) is not enough to obtain a suf-
ficiently low duty cycle at 250 Hz, the output current, in strong overcurrent or short circuit conditions, could in-
crease again.
For this reason the switching frequency is also reduced, so keeping the inductor current under its maximum
threshold.
The frequency depends on the feedback voltage.
As the feedback voltage decreases (due to the reduced duty cycle), the switching frequency decrease too.
Thermal shutdown
The shutdown block generates a signal that turns off the power stage if the temperature of the internal chip goes
higher than a fixed internal threshold (150 ºC).
The sensing element of the chip is very close to the PDMOS area, so ensuring an accurate and fast temperature
detection.
An hysteresis of approximately 20ºC avoids that the devices turns on and off continuously.
Thermal Characteristics
Output voltage programming (GS-R24H(S)0001.5 only)
The GS-R24P output voltage is 5.54V ±4%, to reduce this value connect a resistor between pin 6 (FB) and
pin 5 (Vout-c).
The resistor must be located very close to the proper pins, to minimize the injected noise (see figure 1).
The resistor value is calculated using the following formula:
Rv=[(Vout-1.235)*11.3]/(5.54-Vout) --[kOhm]
Vout can be adjusted between 1.235V (Rv=0 Ohm) and 5.54V (Rv=open)
5/7
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for GS-R24P electronic component. |
Information | Total 7 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ GS-R24P.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
GS-R24F | The function is DC/DC Converter Modules. ST Microelectronics | |
GS-R24FP | The function is DC/DC Converter Modules. ST Microelectronics | |
GS-R24P | The function is STEP-DOWN SWITCHING REGULATOR FAMILY. ST Microelectronics | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
GS-R
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |