ST95040 Datasheet PDF - ST Microelectronics
Part Number | ST95040 | |
Description | (ST950x0) 4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe | |
Manufacturers | ST Microelectronics | |
Logo | ||
There is a preview and ST95040 download ( pdf file ) link at the bottom of this page. Total 18 Pages |
Preview 1 page No Preview Available ! ST95040
ST95020, ST95010
4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe
1 MILLION ERASE/WRITE CYCLES
40 YEARS DATA RETENTION
SINGLE SUPPLY VOLTAGE
– 4.5V to 5.5V for ST950x0
– 2.5V to 5.5V for ST950x0W
SPI BUS COMPATIBLE SERIAL INTERFACE
2 MHz CLOCK RATE MAX
BLOCK WRITE PROTECTION
STATUS REGISTER
16 BYTE PAGE MODE
WRITE PROTECT
SELF-TIMED PROGRAMMING CYCLE
E.S.D.PROTECTION GREATER than 4000V
SUPPORTS POSITIVE CLOCK SPI MODES
8
1
PSDIP8 (B)
0.25mm Frame
8
1
SO8 (M)
150mil Width
Figure 1. Logic Diagram
DESCRIPTION
The ST950x0 is a family of Electrically Erasable
Programmable Memories (EEPROM) fabricated
with STMicroelectronics’s High Endurance Single
Polysilicon CMOS technology. Each memory is
accessed by a simple SPI bus compatible serial
interface. The bus signals are a serial clock input
(C), a serial data input (D) and a serial data output
(Q).
Table 1. Signal Names
C Serial Clock
D Serial Data Input
Q Serial Data Output
S Chip Select
W Write Protect
HOLD
Hold
VCC Supply Voltage
VSS Ground
VCC
D
C
S
W
HOLD
ST950x0
Q
VSS
AI01435B
June 1998
1/18
|
|
Figure 5. Block Diagram
ST95040, ST95020, ST95010
HOLD
W
S
C
D
Q
Control Logic
High Voltage
Generator
I/O Shift Register
Address Register
and Counter
Data
Register
Status
Block
Protect
16 Bytes
X Decoder
AI01272
During a write to the memory operation to the
memory array, all bits BP1, BP0, WEL, WIP are
valid and can be read. During a write to the status
register, only the bits WEL and WIP are valid and
can be read. The values of BP1 and BP0 read at
that time correspondto the previouscontents of the
status register.
The Write-In-Process (WIP) read-only bit indicates
whether the Memory is busy with a write operation.
When set to a ’1’ a write is in progress, when set to
a ’0’ no write is in progress.
The Write Enable Latch (WEL) read-only bit indi-
cates the status of the write enable latch. When set
to a ’1’ the latch is set, when set to a ’0’ the latch is
reset. The Block Protect (BP0 and BP1) bits indi-
cate the extent of the protection employed. These
bits are set by the user issuing the WRSR instruc-
tion. These bits are non-volatile.
5/18
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ST95040 electronic component. |
Information | Total 18 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ ST95040.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
ST95040 | The function is (ST950x0) 4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe. ST Microelectronics | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
ST95
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |