DataSheet39.com

What is 74AUP1G126?

This electronic component, produced by the manufacturer "NXP Semiconductors", performs the same function as "Low-Power buffer/line driver 3-state".


74AUP1G126 Datasheet PDF - NXP Semiconductors

Part Number 74AUP1G126
Description Low-Power buffer/line driver 3-state
Manufacturers NXP Semiconductors 
Logo NXP Semiconductors Logo 


There is a preview and 74AUP1G126 download ( pdf file ) link at the bottom of this page.





Total 20 Pages



Preview 1 page

No Preview Available ! 74AUP1G126 datasheet, circuit

74AUP1G126
Low-power buffer/line driver; 3-state
Rev. 01 — 25 July 2005
Product data sheet
1. General description
The 74AUP1G126 is a high-performance, low-power, low-voltage, Si-gate CMOS device,
superior to most advanced CMOS compatible TTL families.
Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall
times across the entire VCC range from 0.8 V to 3.6 V.
This device ensures a very low static and dynamic power consumption across the entire
VCC range from 0.8 V to 3.6 V.
This device is fully specified for partial Power-down applications using IOFF.
The IOFF circuitry disables the output, preventing the damaging backflow current through
the device when it is powered down.
The 74AUP1G126 provides the single non-inverting buffer/line driver with 3-state output.
The 3-state output is controlled by the output enable input (OE). A LOW level at pin OE
causes the output to assume a high-impedance OFF-state.
This device has the input-disable feature, which allows floating input signals. The inputs
are disabled when the output enable input OE is LOW.
2. Features
s Wide supply voltage range from 0.8 V to 3.6 V
s High noise immunity
s Complies with JEDEC standards:
x JESD8-12 (0.8 V to 1.3 V)
x JESD8-11 (0.9 V to 1.65 V)
x JESD8-7 (1.2 V to 1.95 V)
x JESD8-5 (1.8 V to 2.7 V)
x JESD8-B (2.7 V to 3.6 V)
s ESD protection:
x HBM JESD22-A114-C exceeds 2000 V
x MM JESD22-A115-A exceeds 200 V
x CDM JESD22-C101-C exceeds 1000 V
s Low static power consumption; ICC = 0.9 µA (maximum)
s Latch-up performance exceeds 100 mA per JESD 78 Class II
s Inputs accept voltages up to 3.6 V
s Low noise overshoot and undershoot < 10 % of VCC
s Input-disable feature allows floating input conditions

line_dark_gray
74AUP1G126 equivalent
Philips Semiconductors
74AUP1G126
Low-power buffer/line driver; 3-state
Table 6: Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to
GND (ground = 0 V).
Symbol Parameter
Conditions
Min Max Unit
IGND
Tstg
Ptot
ground current
storage temperature
total power
dissipation
Tamb = 40 °C to +125 °C
-
65
[2] -
50
+150
250
mA
°C
mW
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] For TSSOP5 packages: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K.
For XSON6 packages: above 45 °C the value of Ptot derates linearly with 2.4 mW/K.
10. Recommended operating conditions
Table 7:
Symbol
VCC
VI
VO
Tamb
tr, tf
Recommended operating conditions
Parameter
Conditions
supply voltage
input voltage
output voltage
active mode
ambient temperature
Power-down mode; VCC = 0 V
input rise and fall times VCC = 0.8 V to 3.6 V
Min Max Unit
0.8 3.6 V
0 3.6 V
0 VCC V
0 3.6 V
40 +125 °C
0 200 ns/V
11. Static characteristics
Table 8: Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min Typ
Tamb = 25 °C
VIH HIGH-state input voltage
VCC = 0.8 V
VCC = 0.9 V to 1.95 V
0.70 × VCC -
0.65 × VCC -
VCC = 2.3 V to 2.7 V
1.6 -
VCC = 3.0 V to 3.6 V
2.0 -
VIL LOW-state input voltage VCC = 0.8 V
--
VCC = 0.9 V to 1.95 V
--
VCC = 2.3 V to 2.7 V
--
VCC = 3.0 V to 3.6 V
--
Max Unit
-V
-V
-V
-V
0.30 × VCC V
0.35 × VCC V
0.7 V
0.9 V
9397 750 14686
Product data sheet
Rev. 01 — 25 July 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
5 of 20


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 74AUP1G126 electronic component.


Information Total 20 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 74AUP1G126.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
74AUP1G125The function is Low-power buffer/line driver 3-state. NXP SemiconductorsNXP Semiconductors
74AUP1G125The function is SINGLE BUFFER GATE. DiodesDiodes
74AUP1G126The function is Low-Power buffer/line driver 3-state. NXP SemiconductorsNXP Semiconductors

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

74AU     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search