1300 Datasheet PDF - Nihon Dempa Kogyo
Part Number | 1300 | |
Description | Crystal Clock Oscillators | |
Manufacturers | Nihon Dempa Kogyo | |
Logo | ||
There is a preview and 1300 download ( pdf file ) link at the bottom of this page. Total 5 Pages |
Preview 1 page No Preview Available ! CRYSTAL CLOCK
OSCILLATORS
WARRANTY CLAUSE
s 1300 Series
No. Item
Condition
1 Vibration Test
MIL-STD-202F, TM204D, condition B
2 Shock Test
MIL-STD-202F, TM213B, condition 9,800m/s2 0.5 ms
3 Drop Test
3 times natural drops on to hard wooden board from the height (see 4 )
4 Humidity Test
MIL-STD-202F, TM103B, condition A
5 Solder Heat Test MIL-STD-202F, TM210A, condition B (260°C ± 5°C for 10 ± 1 seconds)
6 Thermal Shock Test Expose to 100 cycles of extreme temperatures, that is, –40°C for 30 minutes then +85°C for 30 minutes.
7 Terminal Strength Test MIL-STD-202F, TM211A, condition A (Pull Weighting 0.907 kg) and condition C (Bend Weighting 0.45 kg)
Specification
Please see
below note. (*)
Please see
below note. (*)
Please see
below note. (*)
Please see
below note. (*)
Please see
below note. (*)
Please see
below note. (*)
8 Soldering Test
Soaking in the soldering bath at +235±5°C for 5±1 seconds
More than 90% of lead should be covered by solder.
9
Solvent Resistance
After soaking in alcohol for 30 minutes.
The markings are not faded out.
(*) After the tests mentioned above, the electrical specifications are satisfied. Also frequency deviation before and after test should be F/F <= ±10×10-6
The electrical specifications are frequency tolerance, Lcc, Tr/Tf, VOL/VOH, duty cycle.
Model
1300
Height
50 cm
s 1600 Series
No. Item
Condition
Specification
1. P.C Test
2.
Thermal
Shock Test
3.
Heat Cycle
Test
Temperature: +121±2°C, Pressure: 2
Atmospheric pressure, Time: 48 Hours
1Cycle: –55°C (30minutes)~+125°C (30minutes)
Number of Cycle: 15 cycles is gas phase
1Cycle: –55°C ~ +25°C ~ +125°C ~ +25°C
(30 minutes) (10 minutes) (30 minutes) (10 minutes)
Number of Cycle: 10 cycles
Please see below
note.(*)
Please see below
note.(*)
Please see below
note.(*)
4.
High Temperature
High Humidity Test
Temperature: +85°C, Humidity: 85%,
Time: 250 Hours
5.
+85°C Aging
(non operated)
Temperature: +85°C, Time: 720 Hours
Please see below
note.(*)
Please see below
note.(*)
6.
Vibration
Test
MIL-STD-202F Test Method: 204D,
Test Condition: D (196m/s2 Peak)
Please see below
note.(*)
7. Shock Test
MIL-STD-202F Test Method: 213B
Test Condition: Half Sinusoidal Wave
29,400m/s2 0.5 ms 3 Directions 3 times each
Please see below
note.(*)
8. Drop Test
9.
Soldering
Test
Fall Height: 75 cm, 3 Drops on to Hard
Wooden board
MIL-STD-202F Test Method: 208E
Test Condition: Soaking in the soldering
bath at +245±5°C for 5±1 seconds
Please see below
note.(*)
More than 90% of
lead or Pad should be
covered by solder.
10.
Soldering
Resistance
MIL-STD-202F Test Method: 210A
Test Condition: Soaking in the soldering
bath at +260±5°C for 10±1 seconds
Please see below
note.(*)
11.
Solvent
Resistance
After soaking in each solvent, Freon, tri-
chloro-ethane and alcohol for 30 minutes.
The markings are not
faded out. Also (*)
(*) After the tests mentioned above, the electrical specifications are satisfied. Also frequency
deviation before and after test should be F/F <= ±10×10-6
The electrical specifications are frequency tolerance, Lcc, Tr/Tf, VOL/VOH, duty cycle.
100
|
|
CRYSTAL CLOCK
OSCILLATORS
s 2500 Series
MARKING
NK : 2560NK
TK : 2560TK
K : 2570NK
Output Frequency
2500 Series:
8 Including decimal point, 6 digits are marked.
[EX] 14.31818MHz ¡ 14.318
#1 Pin Location
s 2700 Series
: 2700N
T : 2700T
V : 2780V
W : 2770W
Y : 2770Y
Lot No. (2 digits)
Output Frequency
2700 Series:
8 Including decimal point, 6 digits are marked.
[EX] 14.31818MHz ¡ 14.318
#1 Pin Location
Lot No. (3digits)
104
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 1300 electronic component. |
Information | Total 5 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ 1300.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
1300 | The function is Crystal Clock Oscillators. Nihon Dempa Kogyo | |
1300-102-4xx | The function is 2.54mm IDC Connector. Methode Electronics | |
13001 | The function is NPN Epitaxial Silicon Transistor. Elite | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
1300
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |