|
|
PDF SP6128A Data sheet ( Hoja de datos )
| Número de pieza | SP6128A | |
| Descripción | Low Voltage / Synchronous Step Down PWM Controller Ideal for 2A to 10A / Small Footprint / DC-DC Power Converters | |
| Fabricantes | Sipex | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SP6128A (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
® SP6128A
Low Voltage, Synchronous Step Down PWM Controller
Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters
■ Optimized for Single Supply, 3V - 5.5V Applications GL 1
14 BST
■ High Efficiency: Greater Than 95% Possible
■ Discontinuous Startup for Precharged Output
■ Accurate Fixed 300kHz Frequency Operation
PVCC 2
VCC 3
PGND 4
SP6128A
14 pin TSSOP
13 GH
12 SWN
11 ISET
■ Fast Transient Response
GND 5
10 VFB
■ Internal Soft Start Circuit
COMP 6
9 NC
■ Accurate 0.8V Reference Allows Low Output
NC 7
8 NC
Voltages
■ Resistor Programmable Output Voltage
Now Available in Lead Free Packaging
■ Resistor Programmable Overcurrent Threshold
■ Loss-less Current Limit with High Side RDS(ON)
Sensing
■ Hiccup Mode Current Limit Protection
■ Dual N-Channel MOSFET Synchronous Driver
■ Quiescent Current: 500µA, 30µA in Shutdown
APPLICATIONS
■ DSP
■ Microprocessor Core
■ I/O & Logic
■ Industrial Control
■ Distributed Power
■ 14 pin TSSOP
■ Low Voltage Power
DESCRIPTION
The SP6128A is a fixed frequency, voltage mode, synchronous PWM controller designed to
work from a single 5V or 3.3V input supply, providing excellent AC and DC regulation for high
efficiency power conversion. Requiring only few external components, the SP6128A pack-
aged in an 14-pin TSSOP, is especially suited for low voltage applications where cost, small
size and high efficiency are critical. The operating frequency is internally set to 300kHz,
allowing small inductor values and minimizing PC board space. The SP6128A drives two
N-channel power MOSFETs for improved efficiency and includes an accurate 0.8V reference
for low output voltage applications.
TYPICAL APPLICATION CIRCUIT
3V to 5.5V
D1
MBR0530
C5
10µF
C6
10µF
C7
10µF
R1
5
C1
2.2µF
1 GL
14
BST
2 PVCC SP6128A GH 13
3 VCC
12
SWN
4
PGND
5 GND
11
ISET
VFB 10
6
COMP
9
NC
7
NC
NC 8
Q1
C4
R3 FDS6690A
8k
1µF
Q2
FDS6690A
C3
68pF
R2 7.87k C2 4.7n
L1 1.0µH
2.5V/10A
D2
STPS2L25U
C8
10µF
C9
10µF
C10 C11
10µF 470µF
C12
4.7nF
R4
1.7k
R5
800
Rev. 05/25/04
SP6128A Low Voltage, Synchronous Step Down PWM Controller
1
© Copyright 2004 Sipex Corporation
1 page  
When the overcurrent threshold is exceeded, the
overcurrent comparator sets the fault latch and
terminates the output pulses. The controller
stops switching and goes through a hiccup se-
quence. This prevents excessive power dissipa-
tion in the external power MOSFETs during an
overload condition. An internal delay circuit
prevents that very short and mild overload con-
ditions, that could occur during a load transient,
activate the current limit circuit.
A low power sleep mode can be invoked in the
SP6128A by externally forcing the COMP pin
below 0.3V. Quiescent supply current in sleep
mode is typically less than 30µA. An internal
5µA pull-up current at the COMP pin brings the
SP6128A out of shutdown mode.
An internal 0.8V 1.5% reference allows out-
put voltage adjustment for low voltage appli-
cations.
The SP6128A also includes an accurate under-
voltage lockout that shuts down the controller
when the input voltage falls below 2.7V. Output
overvoltage protection is achieved by turning
off the high side switch and turning on the low
side N-channel MOSFET 100% of the time.
Enable
Low quiescent mode or “Sleep Mode” is initi-
ated by pulling the COMP pin below 0.3V with
an external open-drain or open-collector tran-
sistor. Supply current is reduced to 30µA (typi-
cal) in shutdown. On power-up, assuming that
VCC has exceeded the UVLO start threshold
(2.8V), an internal 5µA pull-up current at the
COMP pin brings the SP6128A out of shutdown
mode and ensures start-up. During normal oper-
ating conditions and in absence of a fault, an
internal clamp prevents the COMP pin from
swinging below 0.6V. This guarantees that dur-
ing mild transient conditions, due either to line
or load variations, the SP6128A does not enter
shutdown unless it is externally activated.
During Sleep Mode, the high side and low side
MOSFETS are turned off and the internal soft
start voltage is held low.
OPERATION: continued
UVLO
Assuming that there is not shutdown condition
present, then the voltage on the VCC pin deter-
mines operation of the SP6128A. As VCC rises,
the UVLO block monitors VCC and keeps the
high side and low side MOSFETS off and the
internal SS voltage low until VCC reaches 2.8V.
If no faults are present, the SP6128A will ini-
tiate a soft start when VCC exceeds 2.8 V.
Hysteresis (about 100mV) in the UVLO com-
parator provides noise immunity at start-up.
Soft Start
Soft start is required on step-down controllers to
prevent excess inrush current through the power
train during start-up. Typically this is managed
by sourcing a controlled current into a timing
capacitor and then using the voltage across this
capacitor to slowly ramp up either the error amp
reference or the error amp output (COMP). The
control loop creates narrow width driver pulses
while the output voltage is low and allows these
pulses to increase to their steady-state duty
cycle as the output voltage increases to its regu-
lated value. As a result of controlling the induc-
tor volt*second product during startup, inrush
current is also controlled.
In the SP6128A the duration of the soft-start is
controlled by an internal timing circuit that
provides a 0.3V/mS slew-rate, which is used
during startup and overcurrent to set the hiccup
time. The SP6128A implements soft-start by
ramping up the error amplifier reference voltage
providing a controlled slew-rate of the output
voltage, thereby preventing overshoot and in-
rush current at power up.
The presence of the output capacitor creates extra
currentdrawduringstartup. Simplystated,dVOUT/
dt requires an average sustained current in the
output capacitor and this current must be consid-
ered while calculating peak inrush current and
over current thresholds. An approximate expres-
sion to determine the excess inrush current due to
the dVOUT/dt of the output capacitor COUT is:
VOUT
Iinrush = COUT x (0.27 V/ms) x 0.8V
Rev. 05/25/04
SP6128A Low Voltage, Synchronous Step Down PWM Controller
5
© Copyright 2004 Sipex Corporation
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet SP6128A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SP6128A | Low Voltage / Synchronous Step Down PWM Controller Ideal for 2A to 10A / Small Footprint / DC-DC Power Converters | Sipex |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |