|
|
PDF 74HC4067 Data sheet ( Hoja de datos )
| Número de pieza | 74HC4067 | |
| Descripción | 16-channel analog multiplexer/demultiplexer | |
| Fabricantes | Philips | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 74HC4067 (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
|
No Preview Available !
74HC4067; 74HCT4067
16-channel analog multiplexer/demultiplexer
Rev. 6 — 22 May 2015
Product data sheet
1. General description
The 74HC4067; 74HCT4067 is a single-pole 16-throw analog switch (SP16T) suitable for
use in analog or digital 16:1 multiplexer/demultiplexer applications. The switch features
four digital select inputs (S0, S1, S2 and S3), sixteen independent inputs/outputs (Yn), a
common input/output (Z) and a digital enable input (E). When E is HIGH, the switches are
turned off. Inputs include clamp diodes. This enables the use of current limiting resistors
to interface inputs to voltages in excess of VCC.
2. Features and benefits
Input levels S0, S1, S2, S3 and E inputs:
For 74HC4067: CMOS level
For 74HCT4067: TTL level
Low ON resistance:
80 (typical) at VCC = 4.5 V
70 (typical) at VCC = 6.0 V
60 (typical) at VCC = 9.0 V
Specified in compliance with JEDEC standard no. 7A
ESD protection:
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V
CDM JESD22-C101E exceeds 1000 V
Multiple package options
Specified from 40 C to +85 C and 40 C to +125 C
Typical ‘break before make’ built-in
3. Applications
Analog multiplexing and demultiplexing
Digital multiplexing and demultiplexing
Signal gating
1 page  
NXP Semiconductors
74HC4067; 74HCT4067
16-channel analog multiplexer/demultiplexer
6. Pinning information
6.1 Pinning
+&
+&7
=
<
<
<
<
<
<
<
<
6
6
*1'
9&&
<
<
<
<
<
<
<
<
(
6
6
DDJ
Fig 6. Pin configuration for SO24, SSOP24 and
TSSOP24
WHUPLQDO
LQGH[DUHD
+&
+&7
<
<
<
<
<
<
<
<
6
6
9&&
<
<
<
<
<
<
<
<
(
6
DDJ
7UDQVSDUHQWWRSYLHZ
(1) This is not a supply pin. The substrate is attached to this
pad using conductive die attach material. There is no
electrical or mechanical requirement to solder this pad.
However, if it is soldered, the solder land should remain
floating or be connected to VCC.
Fig 7. Pin configuration for DHVQFN24
6.2 Pin description
Table 2. Pin description
Symbol
Z
Y7, Y6, Y5, Y4, Y3, Y2, Y1, Y0, Y15,
Y14, Y13, Y12, Y11, Y10, Y9, Y8
S0, S1, S3, S2
GND
E
VCC
Pin
1
2, 3, 4, 5, 6, 7, 8, 9, 16, 17, 18, 19, 20, 21, 22, 23
10, 11, 13, 14
12
15
24
Description
common input or output
independent input or output
address input 0
ground (0 V)
enable input (active LOW)
supply voltage
74HC_HCT4067
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 6 — 22 May 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
5 of 28
5 Page 
NXP Semiconductors
74HC4067; 74HCT4067
16-channel analog multiplexer/demultiplexer
Table 7. Static characteristics 74HC4067 …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter
Conditions
Min Typ Max Unit
IS(OFF)
OFF-state leakage current
VCC = 10.0 V; VI = VIH or VIL;
VSW = VCC GND; see Figure 10
per channel
- - 1.0 A
all channels
- - 8.0 A
IS(ON)
ON-state leakage current
VCC = 10.0 V; VI = VIH or VIL;
VSW = VCC GND; see Figure 11
- - 8.0 A
ICC supply current
VI = VCC or GND; Vis = GND or VCC;
Vos = VCC or GND
VCC = 6.0 V
VCC = 10.0 V
- - 160 A
- - 320 A
Table 8. Static characteristics 74HCT4067
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter
Conditions
Min Typ Max Unit
Tamb = 25 C
VIH HIGH-level input voltage
VCC = 4.5 V to 5.5 V
2.0 1.6
-V
VIL
II
IS(OFF)
LOW-level input voltage
input leakage current
OFF-state leakage current
VCC = 4.5 V to 5.5 V
VI = VCC or GND; VCC = 5.5 V
VCC = 5.5 V; VI = VIH or VIL;
VSW = VCC GND; see Figure 10
per channel
- 1.2 0.8 V
- - 0.1 A
- - 0.1 A
all channels
- - 0.8 A
IS(ON)
ICC
ICC
ON-state leakage current
supply current
additional supply current
VCC = 5.5 V; VI = VIH or VIL;
VSW = VCC GND; see Figure 11
VI = VCC or GND; Vis = GND or VCC;
Vos = VCC or GND; VCC = 4.5 V to 5.5 V
per input pin; VI = VCC 2.1 V; other inputs
at VCC or GND; VCC = 4.5 V to 5.5 V
pin E
- - 0.8 A
- - 8.0 A
- 60 216 A
pin Sn
- 50 180 A
CI input capacitance
Tamb = 40 C to +85 C
VIH HIGH-level input voltage
VIL LOW-level input voltage
II input leakage current
IS(OFF)
OFF-state leakage current
VCC = 4.5 V to 5.5 V
VCC = 4.5 V to 5.5 V
VI = VCC or GND; VCC = 5.5 V
VCC = 5.5 V; VI = VIH or VIL;
VSW = VCC GND; see Figure 10
per channel
- 3.5 - pF
2.0 -
-V
- - 0.8 V
- - 1.0 A
- - 1.0 A
all channels
- - 8.0 A
74HC_HCT4067
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 6 — 22 May 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
11 of 28
11 Page | ||
| Páginas | Total 28 Páginas | |
| PDF Descargar | [ Datasheet 74HC4067.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 74HC4060 | 14-stage binary ripple counter with oscillator | Philips |
| 74HC4060 | 14-stage binary ripple counter |  NXP Semiconductors |
| 74HC4060-Q100 | 14-stage binary ripple counter | NXP Semiconductors |
| 74HC4060M | High Speed CMOS Logic 14-Stage Binary Counter |  ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |