DataSheet39.com

What is TDA10021HT?

This electronic component, produced by the manufacturer "NXP Semiconductors", performs the same function as "DVB-C channel receiver".


TDA10021HT Datasheet PDF - NXP Semiconductors

Part Number TDA10021HT
Description DVB-C channel receiver
Manufacturers NXP Semiconductors 
Logo NXP Semiconductors Logo 


There is a preview and TDA10021HT download ( pdf file ) link at the bottom of this page.





Total 16 Pages



Preview 1 page

No Preview Available ! TDA10021HT datasheet, circuit

INTEGRATED CIRCUITS
DATA SHEET
TDA10021HT
DVB-C channel receiver
Product specification
Supersedes data of 2000 Jun 21
File under Integrated Circuits, IC02
2001 Oct 01

line_dark_gray
TDA10021HT equivalent
Philips Semiconductors
DVB-C channel receiver
Product specification
TDA10021HT
SYMBOL PIN TYPE(1)
DESCRIPTION
SCLT
20 OD SCLT can be configured to be a control line output or to output the SCL input. This
is controlled by parameter BYPIIC and CTRL_SCLT of register TEST (index 0F).
SCLT is an open-drain output and therefore requires an external pull-up resistor.
ENSERI
21
I when HIGH this pin enables the serial output transport stream through the
boundary scan pins TRST, TDO, TCK, TDI and TMS (serial interface). Must be set
LOW in bist and boundary scan mode.
TCK
22 I/O test clock: an independent clock used to drive the TAP controller in boundary scan
mode. In normal mode of operation, TCK must be set LOW. In serial stream mode,
TCK is the clock output (OCLK).
TDI 23 I/O test data input: the serial input for test data and instruction in boundary scan mode.
In normal mode of operation, TDI must be set LOW. In serial stream mode, the TDI
is the PSYNC output.
VDDDI8
VSSDI8
TRST
24 S digital supply voltage for the core (1.8 V typ.)
25 G digital ground for the core
26 I/O test reset: this active LOW input signal is used to reset the TAP controller in
boundary scan mode. In normal mode of operation, TRST must be set LOW. In
serial stream mode, TRST is the uncorrectable output (UNCOR).
TMS
27 I/O test mode select: this input signal provides the logic levels needed to change the
TAP controller from state to state. In normal mode of operation, TMS must be set to
HIGH. In serial stream mode, TMS is the DEN output.
TDO
GPIO
28 O test data output: this is the serial test output pin used in boundary scan mode.
Serial data is provided on the falling edge of TCK. In serial stream mode, TDO is
the data output (DO).
29 OD GPIO can be configured by the I2C-bus either as:
A Front-End Lock indicator (FEL) (default mode)
An active LOW output interrupt line (IT) which can be configured by the I2C-bus
interface
A control output pin programmable by I2C-bus.
GPIO is an open-drain output and therefore requires an external pull-up resistor.
VDDD33
VSSD33
CTRL
30 S digital supply voltage for the pads (3.3 V typ.)
31 G digital ground for the pads
32 OD CTRL is a control output pin programmable by the I2C-bus. CTRL is an open-drain
output and therefore requires an external pull-up resistor.
UNCOR
33
O uncorrectable packet: this output signal is HIGH when the provided packet is
uncorrectable (during the 188 bytes of the packet). The uncorrectable packet is not
affected by the Reed Solomon decoder, but the MSB of the byte following the sync
byte is forced to logic 1 for the MPEG-2 process: error flag indicator (if RSI and IEI
are set LOW in the I2C-bus table).
PSYNC
34
O pulse synchro: this output signal goes HIGH when the sync byte (0x47) is provided,
then it goes LOW until the next sync byte
OCLK
35 O output clock: this is the output clock for the DO[7:0] data outputs. OCLK is internally
generated depending on which interface is selected.
DEN
36 O data enable: this output signal is HIGH when there is valid data on the output bus
DO[7:0]
2001 Oct 01
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for TDA10021HT electronic component.


Information Total 16 Pages
Link URL [ Copy URL to Clipboard ]
Download [ TDA10021HT.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
TDA10021HTThe function is DVB-C channel receiver. NXP SemiconductorsNXP Semiconductors

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

TDA1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search