DataSheet39.com

What is UMA1017M?

This electronic component, produced by the manufacturer "NXP Semiconductors", performs the same function as "Low-voltage frequency synthesizer for radio telephones".


UMA1017M Datasheet PDF - NXP Semiconductors

Part Number UMA1017M
Description Low-voltage frequency synthesizer for radio telephones
Manufacturers NXP Semiconductors 
Logo NXP Semiconductors Logo 


There is a preview and UMA1017M download ( pdf file ) link at the bottom of this page.





Total 16 Pages



Preview 1 page

No Preview Available ! UMA1017M datasheet, circuit

INTEGRATED CIRCUITS
DATA SHEET
UMA1017M
Low-voltage frequency synthesizer
for radio telephones
Product specification
Supersedes data of November 1994
File under Integrated Circuits, IC03
1995 Jul 10

line_dark_gray
UMA1017M equivalent
Philips Semiconductors
Low-voltage frequency synthesizer
for radio telephones
Product specification
UMA1017M
FUNCTIONAL DESCRIPTION
General
Programmable reference and main dividers drive the
phase detector. Two charge pumps produce phase error
current pulses for integration in an external loop filter.
A hardwired power-down input PON (pin 9) ensures that
the dividers and phase comparator circuits can be
disabled.
The RFI input (pin 6) drives a pre-amplifier to provide the
clock to the first divider stage. The pre-amplifier has a high
input impedance, dominated by pin and pad capacitance.
The circuit operates with signal levels from 50 mV up to
225 mV (RMS), and at frequencies as high as 1.25 GHz.
The high frequency divider circuits use bipolar transistors,
slower bits are CMOS. Divider ratios (512 to 131071)
allow a 1 MHz phase comparison with a 500 MHz RF
input, and a 10 kHz phase comparison with a 1.25 GHz RF
input.
The reference and main divider outputs are connected to
a phase/frequency detector that controls two charge
pumps. The two pumps have a common bias-setting
current that is set by an external resistance. The ratio
between currents in fast and normal operating modes can
be programmed via the 3-wire serial bus. The low current
pump remains active except in power-down. The high
current pump is enabled via the control input FAST (pin 1).
By appropriate connection to the loop filter, dual bandwidth
loops are provided: short time constant during frequency
switching (FAST mode) to speed-up channel changes and
low bandwidth in the settled state (on-frequency) to reduce
noise and breakthrough levels.
The synthesizer speed-up charge pump (CPF) is
controlled by the FAST input in synchronization with phase
detector operation in such a way that potential
disturbances are minimized. The dead zone (caused by
finite time taken to switch the current sources on or off) is
cancelled by feedback from the normal pump output to the
phase detector thereby improving linearity.
An open drain transistor drives the output pin LOCK
(pin 20). It is recommended that the pull-up resistor from
this pin to VDD is chosen to be of sufficient value to keep
the sink current in the LOW state to below 400 µA. The
output will be a current pulse with the duration of the
selected phase error. By appropriate external filtering and
threshold comparison, an out-of-lock or an in-lock flag is
generated. The out-of-lock function can be disabled via the
serial bus.
Serial programming bus
A simple 3-line unidirectional serial bus is used to program
the circuit. The 3 lines are DATA, CLK and E (enable).
The data sent to the device is loaded in bursts framed by
E. Programming clock edges and their appropriate data
bits are ignored until E goes active LOW. The programmed
information is loaded into the addressed latch when E
returns inactive HIGH. Only the last 21 bits serially clocked
into the device are retained within the programming
register. Additional leading bits are ignored, and no check
is made on the number of clock pulses. The fully static
CMOS design uses virtually no current when the bus is
inactive. It can always capture new programmed data
even during power-down.
However when the synthesizer is powered-on, the
presence of a TCXO signal is required at pin 8 (fXTAL) for
correct programming.
Data format
Data is entered with the most significant bit first. The
leading bits make up the data field, while the trailing four
bits are an address field. The UMA1017M uses 4 of the 16
available addresses. These are chosen to allow direct
compatibility with the UAA2072M integrated front-end.
The data format is shown in Table 1. The first entered bit
is p1, the last bit is p21.
The trailing address bits are decoded on the inactive edge
of E. This produces an internal load pulse to store the data
in one of the addressed latches. To ensure that data is
correctly loaded on first power-up, E should be held LOW
and only taken HIGH after having programmed an
appropriate register. To avoid erroneous divider ratios, the
pulse is not allowed during data reads by the frequency
dividers. This condition is guaranteed by respecting a
minimum E pulse width after data transfer. The
corresponding relationship between data fields and
addresses is given in Table 2.
Power-down mode
The device can be powered-down either by hardware PON
or by software sPON. The dividers are on when both PON
and sPON are at logic 1.
When the synthesizer is reactivated after power-down, the
main and reference dividers are synchronized to avoid
possibility of random phase errors on power-up.
1995 Jul 10
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for UMA1017M electronic component.


Information Total 16 Pages
Link URL [ Copy URL to Clipboard ]
Download [ UMA1017M.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
UMA1017MThe function is Low-voltage frequency synthesizer for radio telephones. NXP SemiconductorsNXP Semiconductors

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

UMA1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search