DataSheet39.com

What is U2402B?

This electronic component, produced by the manufacturer "TEMIC Semiconductors", performs the same function as "Fast Charge Controller for NiCd/NiMH Batteries".


U2402B Datasheet PDF - TEMIC Semiconductors

Part Number U2402B
Description Fast Charge Controller for NiCd/NiMH Batteries
Manufacturers TEMIC Semiconductors 
Logo TEMIC Semiconductors Logo 


There is a preview and U2402B download ( pdf file ) link at the bottom of this page.





Total 17 Pages



Preview 1 page

No Preview Available ! U2402B datasheet, circuit

U2402B
Fast Charge Controller for NiCd/NiMH Batteries
Description
The fast-charge battery controller circuit, U2402B, uses
bipolar technology. The IC enables the designer to create
an efficient and economic charge system. The U2402B
incorporates intelligent multiple-gradient battery-
voltage monitoring and mains phase control for power
management. With automatic top-off charging, the
integrated circuit ensures that the charge device stops
regular charging, before the critical stage of overcharging
is achieved. It has two LED driver indications for charge
and temperature status.
Features
D Multiple gradient monitoring
D Temperature window (Tmin/Tmax)
D Exact battery voltage measurement without charge
D Phase control for charge-current regulation
D Top-off and trickle charge function
D Two LED outputs for charge status indication
D Disabling of d2V/dt2 switch-off criteria
during battery formation
D Battery-voltage check
Applications
D Portable power tools
D Laptop/notebook personal computer
D Cellular/cordless phones
D Emergency lighting systems
D Hobby equipment
D Camcorder
Package: DIP18, SO20
18 (20) 17 (19) 16 (18)
14 (15)
13 (14)
12 (13) 11 (12)
4 (4)
1 (1)
Sync
ö
C
ö
R
Phase control
Vöi
Trigger output
Power - on control
VRef
6.5 V/10 mA
Oscillator
Control unit
Gradient
d2V/dt2 and –dV
15 (17)
2 (2)
Power supply
VS = 8 to 26 V
160 mV
Ref
Temp. control
Tmax Sensor
94 8585
5 (5) 6 (6)
7 (8) 8 (9)
Figure 1. Block diagram
TELEFUNKEN Semiconductors
Rev. A3, 14-Nov-96
Status control
Scan path
Battery
detection
VRef = 5 V
VBatt Monitor
0.1 to 4 V
3 (3)
10 (11)
Charge break
output
9 (10)
( ) SO 20, Pins 7 and 16 NC
1 (17)

line_dark_gray
U2402B equivalent
U2402B
Flow Chart Explanation, fosc = 800 Hz
(Figures 2, 3 and 4)
Battery pack insertion disables the voltage lock at battery
detection input Pin 10. All functions in the integrated
circuit are reset. For further description, DIP-pinning is
taken into consideration.
Battery Insertion and –dV Monitoring
The charging procedure will be carried out if battery
insertion is recognised. If the polarity of the inserted
battery is not according to the specification, the fast
charge rate will stop immediately. After the polarity test,
if positive, the defined fast charge rate, IO, begins for the
first 5 minutes according to –dV monitoring. After
5 minutes of charging, the first identification control is
executed.
If the inserted battery has a signal across its terminal of
less than 0.1 V, then the charging procedure is interrupted.
This means that the battery is defective i.e., it is not a
rechargeable battery – “shorted batteries ignored”.
Voltage and temperature measurements across the battery
are carried out during charge break interval (see figure 6),
i.e., currentless or idle measurements.
If the inserted battery is fully charged, the –dV control
will signal a charge stop after six measurements
(approximately 110 seconds). All the above mentioned
functions are recognised during the first 5 minutes
according to –dV method. During this time, +d2V/dt2
remains inactive. In this way the battery is protected from
unnecessary damage.
d2V/dt2-Gradient
If there is no charge stop within the first 5 minutes after
battery insertion, then d2V/dt2 monitoring will be active.
In this actual charge stage, all stop-charge criteria are
active.
When close to the battery’s capacity limit, the battery
voltage curve will typically rise. As long as the +d2V/dt2
stop-charging criteria are met, the device will stop the fast
charge activities.
Top-Off Charge Stage
By charge disconnection through the + d2V/dt2 mode, the
device switches automatically to a defined protective
top-off charge with a pulse rate of 1/4 IO (pulse time,
tp = 5.12 s, period, T = 20.48 s).
The top-off charge time is specified for a time of
20 minutes @ 800 Hz.
Trickle Charge Stage
When top-off charge is terminated, the device switches
automatically to trickle charge with 1/256 IO (tp = 5.12 s,
period = 1310.72 s). The trickle continues until the
battery pack is removed.
Basic Description
Power Supply, Figure 2
The charge controller allows the direct power supply of
8 to 26 V at Pin 15. Internal regulation limits higher input
voltages. Series resistance, R1, regulates the supply
current, IS, to a maximum value of 25 mA. Series
resistance is recommended to suppress the noise signal,
even below 26 V limitation. It is calculated as follows:
wR1min
Vmax–26 V
25 mA
vR1max
Vmin– 8 V
Itot
where
Itot = IS + IRB1 + I1
Vmax, Vmin = Rectified voltage
IS = Current consumption (IC) without load
IRB1 = Current through resistance, RB1
I1 = Trigger current at Pin 1
TELEFUNKEN Semiconductors
Rev. A3, 14-Nov-96
5 (17)


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for U2402B electronic component.


Information Total 17 Pages
Link URL [ Copy URL to Clipboard ]
Download [ U2402B.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
U2402BThe function is Fast Charge Controller for NiCd/NiMH Batteries. TEMIC SemiconductorsTEMIC Semiconductors

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

U240     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search