DataSheet39.com

What is 73K222AL-IGT?

This electronic component, produced by the manufacturer "ETC", performs the same function as "V.22/ V.21/ Bell 212A/ 103 Single-Chip Modem".


73K222AL-IGT Datasheet PDF - ETC

Part Number 73K222AL-IGT
Description V.22/ V.21/ Bell 212A/ 103 Single-Chip Modem
Manufacturers ETC 
Logo ETC Logo 


There is a preview and 73K222AL-IGT download ( pdf file ) link at the bottom of this page.





Total 28 Pages



Preview 1 page

No Preview Available ! 73K222AL-IGT datasheet, circuit

73K222AL
V.22, V.21, Bell 212A, 103
Single-Chip Modem
DESCRIPTION
The 73K222AL is a highly integrated single-chip
modem IC which provides the functions needed to
construct a CCITT V.22, V.21 and Bell 212A
compatible modem, capable of 1200 bit/s full-duplex
operation over dial-up lines. The 73K222AL is an
enhancement of the 73K212L/AL single-chip modem
which adds V.22 and V.21 modes to the Bell 212A and
103 operation of the 73K212AL. In Bell 212A mode,
the 73K222AL provides the normal Bell 212A and 103
functions and employs a 2225 Hz answer tone. The
73K222AL in V.22 mode produces either 550 or 1800
Hz guard tone, recognizes and generates a 2100 Hz
answer tone, and allows 600 bit/s V.22 or 0-300 bit/s
V.21 operation. The 73K222AL integrates analog,
digital, and switched-capacitor array functions on a
single substrate, offering excellent performance and a
high level of functional integration in a single 28-pin
DIP, PLCC and 44-pin TQFP configuration. The
73K222AL operates from a single +5V supply. The
73K222AL is a new version replacing the 73K222L.
The 73K222AL should be specified for all new
designs.
The 73K222AL includes the DPSK and FSK
modulator/demodulator functions, call progress and
handshake tone monitor and a tone generator capable
of tone required for European applications.
(continued)
FEATURES
April 2000
One-chip CCITT V.22, V.21, Bell 212A and Bell
103 standard compatible modem data pump
Full-duplex operation at 0-300 bit/s (FSK) or 600
and 1200 bit/s (DPSK)
Pin and software compatible with other TDK
Semiconductor Corporation K-Series 1-chip
modems
Interfaces
directly
with
standard
microprocessors (8048, 80C51 typical)
Serial or parallel microprocessor bus for control
Serial port for data transfer
Both synchronous and asynchronous modes of
operation including V.22 extended overspeed
Call progress, carrier, precise answer tone
(2100 or 2225 Hz), and long loop detectors
DTMF, and 550 or 1800 Hz guard tone
generators
Test modes available: ALB, DL, RDL, Mark,
Space, Alternating bit patterns
Precise automatic gain control allows 45 dB
dynamic range
CMOS technology for low power consumption
using 60 mW @ 5V
Single +5 volt supply
PLCC and PDIP packages
AD0-AD7
RD
WR
ALE
CS
RESET
INT
TXD
RXD
DATA
BUS
BUFFER
READ
WRITE
CONTROL
LOGIC
STATUS
AND
CONTROL
LOGIC
BLOCK DIAGRAM
8-BIT
BUS
FOR
CONTROL
AND
STATUS
SERIAL
PORT
FOR
DATA
DIGITAL
PROCESSING
TESTS:
ALB, DLB
RDLB
PATTERNS
CLOCK
GENERATOR
FSK
MODULATOR/
DEMODULATOR
PSK
MODULATOR/
DEMODULATOR
SMART
DIALING
&
DETECT
FUNCTIONS
POWER
DTMF &
TONE
GENERATORS
TRANSMIT
FILTER
RECEIVE
FILTER
TXA
RXA

line_dark_gray
73K222AL-IGT equivalent
73K222AL
V.22, V.21, Bell 212A, 103
Single-Chip Modem
PARALLEL MICROPROCESSOR INTERFACE (continued)
NAME
WR
28-PIN
13
TYPE
I
DESCRIPTION
Write. A low on this informs the 73K222AL that data is available on
AD0-AD7 for writing into an internal register. Data is latched on the
rising edge of WR. No data is written unless both WR and the latched
CS are low.
SERIAL MICROPROCESSOR INTERFACE
A0-A2
- I Register Address Selection. These lines carry register addresses and
should be valid during any read or write operation.
DATA
- I/O Serial Control Data. Data for a read/write operation is clocked in or out
on the falling edge of the EXCLK pin. The direction of data flow is
controlled by the RD pin. RD low outputs data. RD high inputs data.
RD - I Read. A low on this input informs the 73K222AL that data or status
information is being read by the processor. The falling edge of the RD
signal will initiate a read from the addressed register. The RD signal
must continue for eight falling edges of EXCLK in order to read all eight
bits of the referenced register. Read data is provided LSB first. Data
will not be output unless the RD signal is active.
WR - I Write. A low on this input informs the 73K222AL that data or status
information has been shifted in through the DATA pin and is available
for writing to an internal register. The normal procedure for a write is to
shift in data LSB first on the DATA pin for eight consecutive falling
edges of EXCLK and then to pulse WR low. Data is written on the
rising edge of WR.
NOTE: The serial control mode is provided by tying ALE high and CS low. In this configuration AD7 becomes
DATA and AD0, AD1 and AD2 become the address only. See timing diagrams on page 20.
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 73K222AL-IGT electronic component.


Information Total 28 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 73K222AL-IGT.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
73K222AL-IGTThe function is V.22/ V.21/ Bell 212A/ 103 Single-Chip Modem. ETCETC

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

73K2     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search