74ALVT162731 Datasheet PDF - NXP Semiconductors
Part Number | 74ALVT162731 | |
Description | 2.5V/3.3V 1-to-4 address register/driver with 30ohm termination resistors 3-State | |
Manufacturers | NXP Semiconductors | |
Logo | ||
There is a preview and 74ALVT162731 download ( pdf file ) link at the bottom of this page. Total 12 Pages |
Preview 1 page No Preview Available ! INTEGRATED CIRCUITS
74ALVT162731
2.5V/3.3V 1-to-4 address register/driver
with 30Ω termination resistors (3-State)
Product specification
IC24 Data Handbook
1999 Mar 23
Philips
Semiconductors
|
|
Philips Semiconductors
2.5V/3.3V 1-to-4 address register/driver with 30Ω
termination resistors (3-State)
Product specification
74ALVT162731
DC ELECTRICAL CHARACTERISTICS (3.3V "0.3V RANGE)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C UNIT
MIN TYP1 MAX
VIK Input clamp voltage
VOH High-level output voltage
VCC = 3.0V; IIK = –18mA
VCC = 3.0V; IOH = –12mA
–0.85 –1.2
2.0 2.5
V
V
VOL Low–level output voltage
VCC = 3.0V; IOL = 12mA
0.5 0.8
V
VRST
II
IOFF
IHOLD
IEX
IPU/PD
Power-up output low voltage6
Input leakage current
Off current
Bus Hold current
Data inputs7
Current into an output in the
High state when VO > VCC
Power up/down 3-State output
current3
VCC = 3.6V; IO = 1mA; VI = VCC or GND
VCC = 3.6V; VI = VCC or GND
VCC = 0 or 3.6V; VI = 5.5V
VCC = 3.6V; VI = VCC
VCC = 3.6V; VI = 0
VCC = 0V; VI or VO = 0 to 4.5V
VCC = 3V; VI = 0.8V
VCC = 3V; VI = 2.0V
VCC = 0V to 3.6V; VCC = 3.6V
Control pins
Data pins4
VO = 5.5V; VCC = 3.0V
VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC
OE/OE = Don’t care
75
–75
±500
0.1
0.1
0.5
0.1
0.1
130
–140
0.55
±1
10
1
-5
±100
10 125
1 ±100
V
µA
µA
µA
µA
µA
IOZH 3-State output High current
VCC = 3.6V; VO = 3.0V; VI = VIL or VIH
0.5 5 µA
IOZL 3-State output Low current
VCC = 3.6V; VO = 0.5V; VI = VIL or VIH
0.5 –5 µA
ICCH
VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0
0.05 0.1
ICCL
ICCZ
Quiescent supply current
VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0
VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO=05
7.0 9.0
0.06 0.1
mA
∆ICC
Additional supply current per
input pin2
VCC = 3V to 3.6V; One input at VCC–0.6V,
Other inputs at VCC or GND
0.04 0.4 mA
NOTES:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.
6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.
7. This is the bus hold overdrive current required to force the input to the opposite logic state.
1999 Mar 23
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 74ALVT162731 electronic component. |
Information | Total 12 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ 74ALVT162731.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
74ALVT162731 | The function is 2.5V/3.3V 1-to-4 address register/driver with 30ohm termination resistors 3-State. NXP Semiconductors | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
74AL
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |