DataSheet39.com

What is 74ACTQ821?

This electronic component, produced by the manufacturer "Fairchild Semiconductor", performs the same function as "Quiet Seriesa 10-Bit D-Type Flip-Flop with 3-STATE Outputs".


74ACTQ821 Datasheet PDF - Fairchild Semiconductor

Part Number 74ACTQ821
Description Quiet Seriesa 10-Bit D-Type Flip-Flop with 3-STATE Outputs
Manufacturers Fairchild Semiconductor 
Logo Fairchild Semiconductor Logo 


There is a preview and 74ACTQ821 download ( pdf file ) link at the bottom of this page.





Total 7 Pages



Preview 1 page

No Preview Available ! 74ACTQ821 datasheet, circuit

March 1990
Revised November 1998
74ACTQ821
Quiet Series10-Bit D-Type Flip-Flop
with 3-STATE Outputs
General Description
The ACTQ821 is a 10-bit D-type flip-flop with non-inverting
3-STATE outputs arranged in a broadside pinout. The
ACTQ821 utilizes Fairchild’s Quiet Seriestechnology to
guarantee quiet output switching and improved dynamic
threshold performance. FACT Quiet Seriesfeatures
GTOoutput control and undershoot corrector in addition
to a split ground bus for superior performance.
Features
s Guaranteed simultaneous switching noise level and
dynamic threshold performance
s Guaranteed pin-to-pin skew AC performance
s Non-inverting 3-STATE outputs for bus interfacing
s 4 kV minimum ESD immunity
s Outputs source/sink 24 mA
s Functionally identical to the AM29821
Ordering Code:
Order Number Package Number
Package Description
74ACTQ821SC
M24B
24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide Body
74ACTQ821SPC
N24C
24-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-100, 0.300” Wide
Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code.
Logic Symbols
Connection Diagram
Pin Assignment
for DIP and SOIC
IEEE/IEC
Pin Descriptions
Pin Names
D0–D9
O0–O9
OE
CP
Description
Data Inputs
Data Outputs
Output Enable Input
Clock Input
FACT, Quiet Series, FACT Quiet Series, and GTOare trademarks of Fairchild Semiconductor Corporation.
© 1999 Fairchild Semiconductor Corporation DS010686.prf
www.fairchildsemi.com

line_dark_gray
74ACTQ821 equivalent
FACT Noise Characteristics
The setup of a noise characteristics measurement is critical
to the accuracy and repeatability of the tests. The following
is a brief description of the setup used to measure the
noise characteristics of FACT.
Equipment:
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
Tektronics Model 7854 Oscilloscope
Procedure:
1. Verify Test Fixture Loading: Standard Load 50 pF,
500.
2. Deskew the HFS generator so that no two channels
have greater than 150 ps skew between them. This
requires that the oscilloscope be deskewed first. It is
important to deskew the HFS generator channels
before testing. This will ensure that the outputs switch
simultaneously.
3. Terminate all inputs and outputs to ensure proper load-
ing of the outputs and that the input levels are at the
correct voltage.
4. Set the HFS generator to toggle all but one output at a
frequency of 1 MHz. Greater frequencies will increase
DUT heating and effect the results of the measure-
ment.
5. Set the HFS generator input levels at 0V LOW and 3V
HIGH for ACT devices and 0V LOW and 5V HIGH for
AC devices. Verify levels with an oscilloscope.
VOLP/VOLV and VOHP/VOHV:
• Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually be
the furthest from the ground pin. Monitor the output volt-
ages using a 50coaxial cable plugged into a standard
SMB type connector on the test fixture. Do not use an
active FET probe.
• Measure VOLP and VOLV on the quiet output during the
worst case transition for active and enable. Measure
VOHP and VOHV on the quiet output during the worst
case active and enable transition.
• Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
VILD and VIHD:
• Monitor one of the switching outputs using a 50coaxial
cable plugged into a standard SMB type connector on
the test fixture. Do not use an active FET probe.
• First increase the input LOW voltage level, VIL, until the
output begins to oscillate or steps out a min of 2 ns.
Oscillation is defined as noise on the output LOW level
that exceeds VIL limits, or on output HIGH levels that
exceed VIH limits. The input LOW voltage level at which
oscillation occurs is defined as VILD.
• Next decrease the input HIGH voltage level VIH until the
output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW level
that exceeds VIL limits, or on output HIGH levels that
exceed VIH limits. The input HIGH voltage level at which
oscillation occurs is defined as VIHD.
• Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
Note 10: VOHV and VOLP are measured with respect to ground reference.
Note 11: Input pulses have the following characteristics: f = 1 MHz,
tr = 3 ns, tf = 3 ns, skew < 150 ps.
FIGURE 1. Quiet Output Noise Voltage Waveforms
FIGURE 2. Simultaneous Switching Test Circuit
5 www.fairchildsemi.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 74ACTQ821 electronic component.


Information Total 7 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 74ACTQ821.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
74ACTQ821The function is Quiet Seriesa 10-Bit D-Type Flip-Flop with 3-STATE Outputs. Fairchild SemiconductorFairchild Semiconductor
74ACTQ821The function is Quiet Series 10-Bit D Flip-Flop. National SemiconductorNational Semiconductor
74ACTQ821LThe function is Quiet Series 10-Bit D Flip-Flop with TRI-STATE Outputs. National SemiconductorNational Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

74AC     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search