DataSheet39.com

What is 74ACTQ18825SSC?

This electronic component, produced by the manufacturer "Fairchild Semiconductor", performs the same function as "18-Bit Buffer/Line Driver with 3-STATE Outputs".


74ACTQ18825SSC Datasheet PDF - Fairchild Semiconductor

Part Number 74ACTQ18825SSC
Description 18-Bit Buffer/Line Driver with 3-STATE Outputs
Manufacturers Fairchild Semiconductor 
Logo Fairchild Semiconductor Logo 


There is a preview and 74ACTQ18825SSC download ( pdf file ) link at the bottom of this page.





Total 7 Pages



Preview 1 page

No Preview Available ! 74ACTQ18825SSC datasheet, circuit

September 1991
Revised January 2000
74ACTQ18825
18-Bit Buffer/Line Driver with 3-STATE Outputs
General Description
The ACTQ18825 contains eighteen non-inverting buffers
with 3-STATE outputs designed to be employed as a mem-
ory and address driver, clock driver, or bus oriented trans-
mitter/receiver. The device is byte controlled. Each byte
has separate 3-STATE control inputs which can be shorted
together for full 18-bit operation.
The ACTQ18825 utilizes Fairchild FACT Quiet Series
technology to guarantee quiet output switching and
improved dynamic threshold performance. FACT Quiet
Series features GTOoutput control and undershoot cor-
rector for superior performance.
Features
s Utilizes Fairchild FACT Quiet Series technology
s Broadside pinout allows for easy board layout
s Guaranteed simultaneous switching noise level and
dynamic threshold performance
s Guaranteed pin-to-pin output skew
s Separate control logic for each byte
s Extra data width for wider address/data paths or buses
carrying parity
s Outputs source/sink 24 mA
s Additional specs for Multiple Output Switching
s Output loading specs for both 50 pF and 250 pF loads
Ordering Code:
Order Number Package Number
Package Description
74ACTQ18825SSC
MS56A
56-Lead Shrink Small Outline Package (SSOP), JEDEC MO-118, 0.300” Wide
74ACTQ18825MTD
MTD56
56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide
Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code.
Logic Symbol
Pin Descriptions
Pin Names
OEn
I0–I17
O0–O17
Description
Output Enable Input (Active LOW)
Inputs
Outputs
FACT, FACT Quiet Seriesand GTOare trademarks of Fairchild Semiconductor Corporation.
© 2000 Fairchild Semiconductor Corporation DS010955
www.fairchildsemi.com

line_dark_gray
74ACTQ18825SSC equivalent
FACT Noise Characteristics
The setup of a noise characteristics measurement is critical
to the accuracy and repeatability of the tests. The following
is a brief description of the setup used to measure the
noise characteristics of FACT.
Equipment:
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
Tektronics Model 7854 Oscilloscope
Procedure:
1. Verify Test Fixture Loading: Standard Load 50 pF,
500.
2. Deskew the HFS generator so that no two channels
have greater than 150 ps skew between them. This
requires that the oscilloscope be deskewed first. It is
important to deskew the HFS generator channels
before testing. This will ensure that the outputs switch
simultaneously.
3. Terminate all inputs and outputs to ensure proper load-
ing of the outputs and that the input levels are at the
correct voltage.
4. Set the HFS generator to toggle all but one output at a
frequency of 1 MHz. Greater frequencies will increase
DUT heating and effect the results of the measure-
ment.
Note 14: VOHV and VOLP are measured with respect to ground refer-
ence.
Note 15: Input pulses have the following characteristics: f = 1 MHz,
tr = 3 ns, tf = 3 ns, skew < 150 ps.
FIGURE 1. Quiet Output Noise Voltage Waveforms
5. Set the HFS generator input levels at 0V LOW and 3V
HIGH for ACT devices and 0V LOW and 5V HIGH for
AC devices. Verify levels with an oscilloscope.
VOLP/VOLV and VOHP/VOHV:
• Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually be
the furthest from the ground pin. Monitor the output volt-
ages using a 50coaxial cable plugged into a standard
SMB type connector on the test fixture. Do not use an
active FET probe.
• Measure VOLP and VOLV on the quiet output during the
worst case transition for active and enable. Measure
VOHP and VOHV on the quiet output during the worst
case transition for active and enable
• Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
VILD and VIHD:
• Monitor one of the switching outputs using a 50coaxial
cable plugged into a standard SMB type connector on
the test fixture. Do not use an active FET probe.
• First increase the input LOW voltage level, VIL, until the
output begins to oscillate or steps out a min of 2 ns.
Oscillation is defined as noise on the output LOW level
that exceeds VIL limits, or on output HIGH levels that
exceed VIH limits. The input LOW voltage level at which
oscillation occurs is defined as VILD.
• Next decrease the input HIGH voltage level, VIH, until
the output begins to oscillate or steps out a min of 2 ns.
Oscillation is defined as noise on the output LOW level
that exceeds VIL limits, or on output HIGH levels that
exceed VIH limits. The input HIGH voltage level at which
oscillation occurs is defined as VIHD.
• Verify that the GND reference recorded on the oscillo-
scope has not drifted to ensure the accuracy and repeat-
ability of the measurements.
FIGURE 2. Simultaneous Switching Test Circuit
5 www.fairchildsemi.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for 74ACTQ18825SSC electronic component.


Information Total 7 Pages
Link URL [ Copy URL to Clipboard ]
Download [ 74ACTQ18825SSC.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
74ACTQ18825SSCThe function is 18-Bit Buffer/Line Driver with 3-STATE Outputs. Fairchild SemiconductorFairchild Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

74AC     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search