DataSheet39.com

What is FDS6612A?

This electronic component, produced by the manufacturer "Microsemi Corporation", performs the same function as "EVALUATION KIT".


FDS6612A Datasheet PDF - Microsemi Corporation

Part Number FDS6612A
Description EVALUATION KIT
Manufacturers Microsemi Corporation 
Logo Microsemi Corporation Logo 


There is a preview and FDS6612A download ( pdf file ) link at the bottom of this page.





Total 18 Pages



Preview 1 page

No Preview Available ! FDS6612A datasheet, circuit

LXE1710 EVALUATION BOARD
USER GUIDE
 
   
 

A MICROSEMI COMPANY
Copyright © 2000
Rev. 1.1, 2000-12-01
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1

line_dark_gray
FDS6612A equivalent
LXE1710 EVALUATION BOARD
USER GUIDE
QUICK START GUIDE
The LXE1710 Evaluation Board is a fully functional,
Class-D Amplifier. Connection to a single supply
voltage (VDD from either a battery or power supply),
speakers, and your audio source is all that is required
to begin evaluating the amplifier and listening to music.
The following outlines the necessary connections and
control jumpers.
1) Verify contents of Evaluation Kit: The easy-to-
use amplifier is all contained on a single board.
Visually inspect to see if the board or any
components were damaged during shipping.
All components are located on the top side of
the PCB except for the decoupling capacitor,
C17. A copy of the LX1710/1711 Datasheet
should also be enclosed or a PDF version can
be downloaded from the Microsemi.com
website
(http://www.microsemi.com/datasheets/MSC1580.PDF).
2) Power and Ground Connections: The voltage
supply and ground connections are made
through terminal block TB1. Connect your “+”
(+7V to +15V) power supply or battery to the
+V input of TB1. Connect your supply or
battery ground to the GND input of TB1.
Please ensure the correct positive and ground
connections are made before turning on the
power supply.
3) Speaker Connection: The amplifier is designed
   $  ! #" 
“+” and “-“ to the +OUT and –OUT input of
terminal block TB2 respectively. The amplifier
Jumper
toward
OFF
J1 Jumper:
Amplifier
enabled
SLEEP/
(SLEEP/ is
OFF)
J2 Jumper:
Audio Input
enabled
MUTE
(MUTE is
OFF)
  Jumper Settings
Jumper
toward
ON
Amplifier
disabled
(SLEEP/ is
ON)
Audio Input
disabled
(MUTE is ON)
Jumper
floating
Amplifier
disabled
(SLEEP/ is
ON)
Audio Input
enabled
(MUTE is
OFF)
can be used to drive other speaker loads but
frequency response may not be optimal. See
LC filter design section for recommended
inductor and capacitor modifications.
4) Audio Input Connection: Connect your audio
source to the RCA Jack CN1, Audio In. For
other type interfaces, the audio input signal can
also be connected to the amplifier board using
the J3 (In- and In+) location. Strip Line Plugs
can be inserted into J3 for connectivity.
5) Jumper Selection Controls: The “on/off” or
enable to the module is controlled with the
SLEEP/ signal. Jumper J1 connects the
SLEEP/ to “on” or “ off”. SLEEP/ is an active
Low control. Jumper J2 connects the MUTE
control which enables/disables the audio input
to the amplifier. MUTE is an active High signal.
See table below.
6) Power Source: If a power supply is being used,
make sure it is set to the correct voltage level
and turn the power supply on.
7) Audio Source: Make sure the audio source
signal is set to a minimum level. Start or “play”
audio source and adjust source volume to
desired level.
8) Listen to AudioMAX: If the amplifier is not
operating properly, verify preceding steps or
contact Linfinity for technical assistance (714)
898-8121.
To Speaker + To Speaker -
To Power Supply +V
7V-15V for LX1710
7V-25V for LX1711
To Power Supply
Ground
Optional
Audio In -
Optional
Audio In +
To Audio
Source
Copyright © 2000
Rev. 1.1, 2000-12-01
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for FDS6612A electronic component.


Information Total 18 Pages
Link URL [ Copy URL to Clipboard ]
Download [ FDS6612A.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
FDS6612AThe function is PowerTrench MOSFET. Fairchild SemiconductorFairchild Semiconductor
FDS6612AThe function is EVALUATION KIT. Microsemi CorporationMicrosemi Corporation

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

FDS6     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search