DataSheet39.com

What is R1211NC12D?

This electronic component, produced by the manufacturer "IXYS", performs the same function as "Distributed Gate Thyristor".


R1211NC12D Datasheet PDF - IXYS

Part Number R1211NC12D
Description Distributed Gate Thyristor
Manufacturers IXYS 
Logo IXYS Logo 


There is a preview and R1211NC12D download ( pdf file ) link at the bottom of this page.





Total 12 Pages



Preview 1 page

No Preview Available ! R1211NC12D datasheet, circuit

Distributed gate thyristor type R1211NC12x
Date:- 01 August 2012
Data Sheet Issue:- 3
Distributed Gate Thyristor
Type R1211NC12x
Absolute Maximum Ratings
VDRM
VDSM
VRRM
VRSM
VOLTAGE RATINGS
Repetitive peak off-state voltage, (note 1)
Non-repetitive peak off-state voltage, (note 1)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
IT(AV)
IT(AV)
IT(AV)
IT(RMS)
IT(d.c.)
ITSM
ITSM2
I2t
I2t
(di/dt)cr
VRGM
PG(AV)
PGM
VGD
THS
Tstg
OTHER RATINGS
Mean on-state current, Tsink=55°C, (note 2)
Mean on-state current. Tsink=85°C, (note 2)
Mean on-state current. Tsink=85°C, (note 3)
Nominal RMS on-state current, Tsink=25°C, (note 2)
D.C. on-state current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, VRM=0.6VRRM, (note 5)
Peak non-repetitive surge tp=10ms, VRM10V, (note 5)
I2t capacity for fusing tp=10ms, VRM=0.6VRRM, (note 5)
I2t capacity for fusing tp=10ms, VRM10V, (note 5)
Maximum rate of rise of on-state current (repetitive), (Note 6)
Maximum rate of rise of on-state current (non-repetitive), (Note 6)
Peak reverse gate voltage
Mean forward gate power
Peak forward gate power
Non-trigger gate voltage, (Note 7)
Operating temperature range
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 125°C Tj initial.
6) VD=67% VDRM, IFG=2A, tr0.5µs, Tcase=125°C.
7) Rated VDRM.
Data Sheet Type R1211NC12x Issue 3
Page 1 of 12
MAXIMUM
LIMITS
1200
1200
1200
1300
UNITS
V
V
V
V
MAXIMUM
LIMITS
1211
771
424
2497
1927
17.6
19.4
15.48×105
18.82×105
1000
1500
5
2
30
0.25
-40 to +125
-40 to +150
UNITS
A
A
A
A
A
kA
kA
A2s
A2s
A/µs
A/µs
V
W
W
V
°C
°C
August 2012

line_dark_gray
R1211NC12D equivalent
Distributed gate thyristor type R1211NC12x
The total dissipation is now given by:
W(TOT) = W (original) + E f
12.2 Determination without Measurement
In circumstances where it is not possible to measure voltage and current conditions, or for design
purposes, the additional losses E in joules may be estimated as follows.
Let E be the value of energy per reverse cycle in joules (curves in Figure 9).
Let f be the operating frequency in Hz
( )TSINK (new) = TSINK (original ) E Rth f
Where TSINK (new) is the required maximum heat sink temperature and
TSINK (original) is the heat sink temperature given with the frequency ratings.
A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage
to a peak value (Vrm) of 67% of the maximum grade. If a different grade is being used or Vrm is other than
67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value
obtained from the curves.
NOTE 1- Reverse Recovery Loss by Measurement
This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring
the charge care must be taken to ensure that:
(a) a.c. coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation
of this snubber is shown below:
R2 = 4 Vr
Cs di dt
Where: Vr = Commutating source voltage
CS = Snubber capacitance
R = Snubber resistance
13.0 Gate Drive
The recommended pulse gate drive is 30V, 15with a short-circuit current rise time of not more than
0.5µs. This gate drive must be applied when using the full di/dt capability of the device.
The duration of pulse may need to be configured with respect to the application but should be no shorter
than 20µs, otherwise an increase in pulse current could be needed to supply the resulting increase in
charge to trigger.
Data Sheet Type R1211NC12x Issue 3
Page 5 of 12
August 2012


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for R1211NC12D electronic component.


Information Total 12 Pages
Link URL [ Copy URL to Clipboard ]
Download [ R1211NC12D.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
R1211NC12CThe function is Distributed Gate Thyristor. IXYSIXYS
R1211NC12DThe function is Distributed Gate Thyristor. IXYSIXYS
R1211NC12EThe function is Distributed Gate Thyristor. IXYSIXYS

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

R121     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search