|
|
PDF TSOP59356 Data sheet ( Hoja de datos )
| Número de pieza | TSOP59356 | |
| Descripción | IR Receiver Modules | |
| Fabricantes | Vishay | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TSOP59356 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
Not for New Design - Replaced by New TSOP581../583../591../593../595.. (#82462)
TSOP581.., TSOP583.., TSOP591.., TSOP593..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
19026
MECHANICAL DATA
Pinning for TSOP581.., TSOP583..:
1 = OUT, 2 = GND, 3 = VS
Pinning for TSOP591.., TSOP593..:
1 = OUT, 2 = VS, 3 = GND
FEATURES
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.7 V to 5.5 V
• Suitable for short bursts: burst length ≥ 6 carrier
cycles
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
DESCRIPTION
These products are miniaturized receiversfor infrared
remote control systems. A PIN diode and a preamplifier are
assembled on a lead frame, the epoxy package acts as an
IR filter.
The demodulated output signal can directly be decoded by
a microprocessor. The main benefit of the TSOP581..,
TSOP591.. is the compatibility to all IR remote control data
formats. The TSOP583.., TSOP593 are optimized to better
suppress spurious pulses from fluorescent lamps, LCD TVs
or plasma displays.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER
FREQUENCY
SHORT BURST AND HIGH DATA RATE
(AGC1)
NOISY ENVIRONMENTS AND SHORT BURSTS
(AGC3)
PINNING
30 kHz
1 = OUT, 2 = GND, 3 = VS
TSOP58130
1 = OUT, 2 = VS, 3 = GND
TSOP59130
1 = OUT, 2 = GND, 3 = VS
TSOP58330
1 = OUT, 2 = VS, 3 = GND
TSOP59330
33 kHz
TSOP58133
TSOP59133
TSOP58333
TSOP59333
36 kHz
TSOP58136
TSOP59136
TSOP58336
TSOP59336
38 kHz
TSOP58138
TSOP59138
TSOP58338
TSOP59338
40 kHz
TSOP58140
TSOP59140
TSOP58340
TSOP59340
56 kHz
TSOP58156
TSOP59156
TSOP58356
TSOP59356
BLOCK DIAGRAM
16833_14
33 kΩ
Input
AGC
Band
pass
Demo-
dulator
PIN Control circuit
3
1
2
Rev. 1.8, 22-Mar-12
APPLICATION CIRCUIT
17170_7
Transmitter IR receiver
with
TSALxxxx
VS
OUT
GND
R1
C1
VO
+ VS
µC
GND
The external components R1 and C1 are optional
to improve the robustness against electrical overstress
(typical values are R1 = 100 Ω, C1 = 0.1 µF).
The output voltage VO should not be pulled down to a level
below 1 V by the external circuit.
The capacitive load at the output should be less than 2 nF.
1 Document Number: 81398
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1 page  
Not for New Design - Replaced by New TSOP581../583../591../593../595.. (#82462)
TSOP581.., TSOP583.., TSOP591.., TSOP593..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
These products are designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the IR receiver in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
• Modulated IR signals from common fluorescent lamps
(example of noise pattern is shown in fig. 15 or fig. 16)
0
16920
5 10 15
Time (ms)
20
Fig. 15 - IR Signal from Fluorescent Lamp
with Low Modulation
0
16921
5 10 15
Time (ms)
20
Fig. 16 - IR Signal from Fluorescent Lamp
with High Modulation
Minimum burst length
After each burst of length
a minimum gap time is required of
For bursts greater than
a minimum gap time in the data stream is needed of
Maximum number of continuous short bursts/second
Recommended for NEC code
Recommended for RC5/RC6 code
Recommended for Sony code
Recommended for RECS-80 code
Recommended for RCMM code
Recommended for r-step code
Recommended for XMP code
Suppression of interference from fluorescent lamps
TSOP581.., TSOP591..
6 cycles/burst
6 to 70 cycles
≥ 10 cycles
70 cycles
> 1.1 x burst length
2000
yes
yes
yes
yes
yes
yes
yes
Common disturbance signals are
supressed (e.g. waveform of figure 15)
TSOP583.., TSOP593..
6 cycles/burst
6 to 35 cycles
≥ 10 cycles
35 cycles
> 6 x burst length
2000
yes
yes
yes
yes
yes
yes
yes
Even critical disturbance signals are
suppressed (e.g. waveform of figure 16)
Note
• For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP582.., TSOP592.., TSOP584.., TSOP594..
Rev. 1.8, 22-Mar-12
5 Document Number: 81398
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet TSOP59356.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TSOP59356 | IR Receiver Modules | Vishay |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |