|
|
PDF ISL23345 Data sheet ( Hoja de datos )
| Número de pieza | ISL23345 | |
| Descripción | Low Voltage Digitally Controlled Potentiometer | |
| Fabricantes | Intersil | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL23345 (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
Quad, 256 Tap, Low Voltage Digitally ControlledNORTECROEMCOMMENMDEENDIDSERLD2E3PF3LO2A5RCNEEMWENDTEPSAIGRNTS
Potentiometer (XDCP™)
ISL23345
The ISL23345 is a volatile, low voltage, low noise, low power,
256 tap, quad digitally controlled potentiometer (DCP) with an
I2C Bus™ interface. It integrates four DCP cores, wiper switches
and control logic on a monolithic CMOS integrated circuit.
Each digitally controlled potentiometer is implemented with a
combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
I2C bus interface. Each potentiometer has an associated
volatile Wiper Register (WRi, i = 0, 1, 2, 3) that can be directly
written to and read by the user. The contents of the WRi
controls the position of the wiper. When powered on, the wiper
of each DCP will always commence at mid-scale (128 tap
position).
The low voltage, low power consumption, and small package
of the ISL23345 make it an ideal choice for use in battery
operated equipment. In addition, the ISL23345 has a VLOGIC
pin allowing down to 1.2V bus operation, independent from the
VCC value. This allows for low logic levels to be connected
directly to the ISL23345 without passing through a voltage
level shifter.
The DCP can be used as a three-terminal potentiometer or as a
two-terminal variable resistor in a wide variety of applications
including control, parameter adjustments, and signal processing.
Applications
• Power supply margining
• Trimming sensor circuits
• Gain adjustment in battery powered instruments
• RF power amplifier bias compensation
Features
• Four potentiometers per package
• 256 resistor taps
• 10k 50kor 100k total resistance
• I2C serial interface
- No additional level translator for low bus supply
- Three address pins allow up to eight devices per bus
• Maximum supply current without serial bus activity
(standby)
- 5µA @ VCC and VLOGIC = 5V
- 2µA @ VCC and VLOGIC = 1.7V
• Shutdown Mode
- Forces the DCP into an end-to-end open circuit and RWi is
connected to RLi internally
- Reduces power consumption by disconnecting the DCP
resistor from the circuit
• Power supply
- VCC = 1.7V to 5.5V analog power supply
- VLOGIC = 1.2V to 5.5V I2C bus/logic power supply
• Wiper resistance: 70 typical @ VCC = 3.3V
• Power-on preset to mid-scale (128 tap position)
• Extended industrial temperature range: -40°C to +125°C
• 20 Ld TSSOP or 20 QFN packages
• Pb-free (RoHS compliant)
10000
8000
6000
4000
2000
0
0 64 128 192
TAP POSITION (DECIMAL)
FIGURE 1. FORWARD AND BACKWARD RESISTANCE vs TAP
POSITION, 10kΩ DCP
256
VREF
RH1
1 DCP
of
ISL23345
RW1
RL1
-
+
ISL28114
VREF_M
FIGURE 2. VREF ADJUSTMENT
June 21, 2011
FN7872.0
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2011. All Rights Reserved
Intersil (and design) and XDCP are trademarks owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners
1 page  
ISL23345
Analog Specifications VCC = 2.7V to 5.5V, VLOGIC = 1.2V to 5.5V over recommended operating conditions unless otherwise
stated. Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN MAX
(Note 20) TYP (Note 8) (Note 20) UNITS
VOLTAGE DIVIDER MODE (0V @ RL; VCC @ RH; measured at RW, unloaded)
INL Integral Non-linearity, Guaranteed
(Note 13) Monotonic
W option
-1.0
±0.5
+1.0
LSB
(Note 9)
U, T option
-0.5
±0.15
+0.5
LSB
(Note 9)
DNL Differential Non-linearity, Guaranteed W option
(Note 12) Monotonic
-1
±0.4
+1 LSB
(Note 9)
U, T option
-0.4
±0.1
+0.4
LSB
(Note 9)
FSerror Full-scale Error
(Note 11)
W option
-5 -2 0 LSB
(Note 9)
U, T option
-2 -0.5 0 LSB
(Note 9)
ZSerror Zero-scale Error
(Note 10)
W option
0 2 5 LSB
(Note 9)
U, T option
0 0.4 2 LSB
(Note 9)
Vmatch DCP to DCP Matching
(Note 22)
DCPs at same tap position, same voltage at all
RH terminals, and same voltage at all RL
terminals
-2
±0.5
2 LSB
(Note 9)
TCV Ratiometric Temperature Coefficient
(Notes 14)
W option, Wiper Register set to 80 hex
U option, Wiper Register set to 80 hex
8 ppm/°C
4 ppm/°C
T option, Wiper Register set to 80 hex
2.3 ppm/°C
tLS_Settling Large Signal Wiper Settling Time
From code 0 to FF hex, measured from 0 to
1LSB settling of the wiper
300
ns
fcutoff -3dB Cutoff Frequency
Wiper at middle point W option
Wiper at middle point U option
1200
250
kHz
kHz
Wiper at middle point T option
120 kHz
RHEOSTAT MODE (Measurements between RW and RL pins with RH not connected, or between RW and RH with RL not connected)
RINL Integral Non-linearity, Guaranteed
(Note 18) Monotonic
W option; VCC = 2.7V to 5.5V
-2.0
±1
+2.0
MI
(Note 15)
W option; VCC = 1.7V
10.5
MI
(Note 15)
U, T option; VCC = 2.7V to 5.5V
-1.0
±0.3
+1.0
MI
(Note 15)
U, T option; VCC = 1.7V
2.1 MI
(Note 15)
RDNL Differential Non-linearity, Guaranteed W option; VCC = 2.7V to 5.5V
(Note 17) Monotonic
-1 ±0.4 +1 MI
(Note 15)
W option; VCC = 1.7V
±0.6
MI
(Note 15)
U, T option; VCC = 2.7V to 5.5V
-0.5
±0.15
+0.5
MI
(Note 15)
U, T option; VCC = 1.7V
±0.35
MI
(Note 15)
5 FN7872.0
June 21, 2011
5 Page 
ISL23345
Typical Performance Curves (Continued)
0.8 0.50
0.4 0.25
0.0 0.00
-0.4 -0.25
-0.8
0
64 128 192 256
TAP POSITION (DECIMAL)
FIGURE 9. 10k RINL vs TAP POSITION, VCC = 3.3V, +25°C
-0.50
0
64 128 192
TAP POSITION (DECIMAL)
256
FIGURE 10. 50k RINL vs TAP POSITION, VCC = 3.3V, +25°C
100
+25°C
+125°C
80
60
40
-40°C
20
0
0 64 128 192 256
TAP POSITION (DECIMAL)
FIGURE 11. 10k WIPER RESISTANCE vs TAP POSITION, VCC = 3.3V
120
+125°C
100 +25°C
80
60
40 -40°C
20
0
0 64 128 192 256
TAP POSITION (DECIMAL)
FIGURE 12. 50k WIPER RESISTANCE vs TAP POSITION, VCC = 3.3V
400
300
200
100
0
15 63 111 159 207 255
TAP POSITION (DECIMAL)
FIGURE 13. 10k TCv vs TAP POSITION, VCC = 3.3V
80
60
40
20
0
15 63 111 159 207 255
TAP POSITION (DECIMAL)
FIGURE 14. 50k TCv vs TAP POSITION, VCC = 3.3V
11 FN7872.0
June 21, 2011
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet ISL23345.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL23345 | Low Voltage Digitally Controlled Potentiometer | Intersil |
| ISL23348 | Low Voltage Digitally Controlled Potentiometer | Intersil |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |