GT24C32A Datasheet PDF - Giantec Semiconductor
Part Number | GT24C32A | |
Description | 2-WIRE 32K Bits Serial EEPROM | |
Manufacturers | Giantec Semiconductor | |
Logo | ||
There is a preview and GT24C32A download ( pdf file ) link at the bottom of this page. Total 23 Pages |
Preview 1 page No Preview Available ! GT24C32A
GT24C32A
2-WIRE
32K Bits
Serial EEPROM
Copyright © 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any time without
notice. Giantec products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for critical medical or surgical equipment,
aerospace or military, or other applications planned to support or sustain life. It is the customer's obligation to optimize the design in their own products for the best performance
and optimization on the functionality and etc. Giantec assumes no liability arising out of the application or use of any information, products or services described herein. Customers
are advised to obtain the latest version of this device specification before relying on any published information and prior placing orders for products.
Giantec Semiconductor, Inc.
v0
www.giantec-semi.com
1/23
|
|
GT24C32A
4. Pin Configuration
4.1 8-Pin SOIC/SOP, TSSOP and MSOP
Top View
A0
A1
A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
4.2 8-Lead UDFN and XDFN
Top View
A0 1
A1 2
A2 3
GND 4
8 VCC
7 WP
6 SCL
5 SDA
4.3 Pin Definition
Pin No.
1
2
3
4
5
6
7
8
Pin Name
A0
A1
A2
GND
SDA
SCL
WP
VCC
I/O Definition
I Device Address Input
I Device Address Input
I Device Address Input
- Ground
I/O Serial Address, Data input and Data output
I Serial Clock Input
I Write Protect Input
- Power Supply
4.4 Pin Descriptions
SCL
This input clock pin is used to synchronize the data transfer
to and from the device.
SDA
The SDA is a bi-directional pin used to transfer addresses
and data into and out of the device. The SDA pin is an open
drain output and can be wired with other open drain or open
collector outputs. However, the SDA pin requires a pull-up
resistor connected to the power supply.
A0, A1, A2
The A0, A1 and A2 are the device address inputs.
Typically, the A0, A1, and A2 pins are for hardware
addressing and a total of 8 devices can be connected on a
single bus system. When A0, A1, and A2 are left floating,
the inputs are defaulted to zero.
WP
WP is the Write Protect pin. While the WP pin is connected
to the power supply of GT24C32A, the entire array
becomes Write Protected (i.e. the device becomes Read
only). When WP is tied to Ground or left floating, the normal
write operations are allowed.
VCC
Supply voltage
GND
Ground of supply voltage
Giantec Semiconductor, Inc.
v0
www.giantec-semi.com
5/23
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for GT24C32A electronic component. |
Information | Total 23 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ GT24C32A.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
GT24C32A | The function is 2-WIRE 32K Bits Serial EEPROM. Giantec Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
GT24
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |